MSP430FR6989 code composer studio
Write a program that will light LED1, whenever S1 is pressed. It should turn off whenever S1 is released.
MSP430FR6989 code composer studio Write a program that will light LED1, whenever S1 is pressed. It...
using code composer studio Write a program for the msp430FR6989 to make led1 and led 2 alternate blinking 2. repeat the program to make each led blink 5 times in a sequence, then 5 times simultaneously
i need assembly program with screenshot of output please 1. Write an assembly program that interfaces switches, SW1 and SW2, and LEDs, LED1 and LED2, as follows (You should use interrupts for both switches) [50 pts] Initially, both the LEDs should be turned off. When SW2 is pressed for the first time, LED2 should be turned on. The next time SW2 is pressed, LED2 is turned off. The sequence continues hence each press changes the state of LED2. SW1 controls...
C CODE LANGUAGE. MSP430. #include <msp430fr6989.h> #define redLED BIT0 // Red LED at P1.0 #define greenLED BIT7 // Green LED at P9.7 #define BUT1 BIT1 // Button S1 at P1.1 #define BUT2 BIT2 // Button S2 at P1.2 void main(void) { WDTCTL = WDTPW | WDTHOLD; // Stop the Watchdog timer PM5CTL0 &= ~LOCKLPM5; // Enable the GPIO pins // Configure and initialize LEDs P1DIR |= redLED; // Direct pin as output P9DIR |= greenLED; // Direct pin as output...
Write the following program to be executed on the FPGA board. 1. Write a VHDL model for a code detector as shown in the Figure. The keypad is used to unlock a door. Pressing the start button followed by the sequence red-green-red-blue unlocks the door, no other sequence can open the door. Assume the clock is slowed down and each pressing of a button is detected once. For example when red is pressed it is only detected as pressed for...
Write a program in CircuitPython to run on the FM4E that will turn on the heater for one minute if the button is pressed. The LED should be turned on when the heater is on, and it should go off when the heater turns off after one minute. Make sure your code has comments.
C with Switch and LED (12 pts) Write a C program for the MSP 430, using switch 1 (S1) to control LED1, switch 2 (S2) to control LED2 separately. Use pullup resistors for the switch. LED1 is P1.0, LED2 is P1.1, S1 is P1.6, S2 is P1.7 5. a. b. c. d. if press S1, LED1 is on if press S2, LED2 is on; if press both, both LEDs are on; Make comments on each line of code to explain...
Write a program that will turn a light on when a count reaches 20. The light is then to go off when a count of 30 is reached. (You must use two counters for this problem, and provide a reset function for the counters).
write a code in C on RaspberryPi to have an LED light turn on and off using a push button
Write a C# Windows Forms App code in Visual studio with a "start", "stop", "up", "down", "left" and "right" buttons and a textbox. The textbox should start printing numbers from 1 to 100 on the press of the "start" button and stop printing process immediately on the press of "stop" button. Also create a thread after stop button is pressed to allow manual input from "up", "down", "left" and "right" buttons and print up, down, left or right in the same...
using assembly language in microwoft visual studio write the following code with procedure with correct number of Fib numbers Your program should detect the largest Fib number that can be calculated. Besides storing the result in an array, print them on the screen.