Routing Paths and Subnets
TOTAL POINTS 1
1.Question 1
Let’s see how much you’ve learned about routing paths and subnetting! In this activity, you are given a bunch of source and destination IP address pairs. Your task is to route each of these packets from the correct source network to the correct destination network.
Step 1: You will be presented 8 source and destination IP address pairs in the table below.
Step 2: You will mimic how the packets travel from the source IP address to the destination IP address within the network. Click the network source (the corresponding orange bubble) and click all the networks it needs to use in order to reach the destination network. You will need to click each network in the right order.
Step 3: After you’ve selected the source and destination networks, click the “Check” button. Some of these address pairs may not be represented by the networks available. If that’s the case, click the “Source or destination not present” button. If you make a mistake, click the “Reset” button to try again.
Step 4: Once you have correctly answered a question, move on to the next question by clicking on the next question arrow. There are 8 different questions.
Step 5: After you’ve completed all routing paths listed in the table, close the quiz and click the “Submit Quiz” button for a grade.
Routing Paths and Subnets TOTAL POINTS 1 1.Question 1 Let’s see how much you’ve learned about...
I have to mimic how the packets travel from the source IP address to the destination IP address within the network. How do I solve this?Routing Paths and Subnets 192.168.0.0/24 10.1.0.0/16 192.168.1.64/26 192.168.1.0/26 10.2.1.0/16 172.16.100.0/24
1. To which of the following subnets does IP address 225.3.2.22 belong? 225.3.2.0/24 225.3.2.22/24 225.2.3.0/24 225.0.0.0/24 none of the above Question 2 On which of the following devices does the transport layer NOT run? laptop router cellphone A, B and C none of the above Question 3 What is the source address contained in the discover message sent by a host that is wanting to obtain an IP address? 255.255.255.255 0.0.0.0 the IP address of the server the last IP...
Test Your Understanding 10. a) Distinguish between Step 1 and Step 2 in the routing process. b) If any row other than the default row matches an IPv4 address, why will the router never choose the default row? c) Which rows in Figure 8-11 match 128.171.17.13? (Don't forgst the default row.) Show your calculations for rows that match. d) Which of these is the best-match row? Justify your answer. e) What rows match 172.40.17.6? Show your calculations for rows that...
Question 7(1 point) An attacker to a network is using social engineering to attack a network. This means which of the following? (Select all that apply) a b C d The attacker uses a dictionary attack. The attacker uses packet sniffing. The attacker claims to be from network support. The attacker is sifting through discarded trash. Question 8(1 point) The network administrator suspects that packet sniffing is being used to capture data packets in the network. The network administrator is...
Project 4-3: In the following steps, you will learn more about the PING (Packet Internet Grouper) utility, which can be used on a network running IPv4 to verify that TCP/IP is configured correctly and communicating with the network. A ping test is typically the first thing network professionals try when troubleshooting a TCP/IP connection problem. For this project, you can use any type of workstation that's running TCP/IPv4, preferably one connected to the Internet. The output described in the following...
check my answers for Networking I came up with these answers, can check my answers Question 1: General What data rate is needed to transmit an uncompressed 4" x 6" photograph every second with a resolution of 1200 dots per inch and 24 bits per dot (pixel)? 691,200 kb/s 28.8 kb/s 8.29 Mb/s 829 Mb/s Question 2: Layering "Layering" is commonly used in computer networks because (check all that apply): -It forces all network software to be written in ‘C’....
ANSWER NETWORKS QUESTIONS (MCQS AND CALCULATIONS) QUESTIONS ( 11 - 20) QUESTION 11 1. Consider the following excerpt from a simple server side UDP program: Server.py from socket import * sName=’127.0.0.1’ sSocket=socket(AF_INET,SOCK_DGRAM) sSocket.bind((sName, 12005)) while True: msg, cAddr =sSocket.recvfrom(2048) newMsg = msg.decode().lower() sSocket.sendto(*********************) What code could be used to replace the **********’s in line 8? newMsg.encode(), cAddr newMsg.encode() msg.encode(), cAddr msg.encode() none of the above 1 points QUESTION 12 For a client to obtain an IP address from the local...
Please answer me as soon as possible Quiz Question 1 (1 point) Saved What metric is used to measure bandwidth? Question 1 options: a. msec b. bit/sec c. bytes d. number of packets/sec Question 2 (1 point) Saved Ethernet is one of access network technologies. Question 2 options: True False Question 3 (1 point) Saved Consider two hosts, A and B, connected by a single link of rate R bps. Suppose that the two hosts are separated by m meters,...
The question I need help/answer with is the 3rd photo. The first two photos just aid the 3rd Comprehensive Properties All work must be completed using this Excel spreadsheet Al journal entries francial statements, et must be prepared in dean, proper form. Reference your textbook and past courses for examples or templates to model Uue the current year for din purpose This project is W ed 120 points. The grading rubricis valable on the last sheet labeled "Grading brie Wformation...