3.-11 points OSUniPhys1 14.3.WA 022 The weight of a hydraulic barber's chair with a client is...

Question

Question

Answer 1

Answer #1

out put force = Fout = 2000 N

input force = Fin = 49 N

Pin = Pout

pressure P = F / A

Arseą Afn 2 ア y) 2D0D 49 in moj- = 6,39

Answer 2

Similar Homework Help Questions

A dentist's chair with a patient in it weighs 1590 N. The output plunger of a...

A dentist's chair with a patient in it weighs 1590 N. The output plunger of a hydraulic system begins to lift the chair, when the dentist's foot applies a force of 43.1 N to the input piston. Neglect any height difference between the plunger and the piston. What is the ratio of the radius of the plunger to the radius of the piston?
A barber’s chair with a person in its weighs 2100 N. the output plunger of a...

A barber’s chair with a person in its weighs 2100 N. the output plunger of a hydraulic system begins to lift the chair when the barber’s foot applies a force of 55 N to the input piston. Neglect any height difference between the plunger and the piston. What is the radio of the radius of the plunger to the radius of the piston?
The hydraulic oil in a car lift has a density of 8.17x10^2 kg/m^3. The weight of...

The hydraulic oil in a car lift has a density of 8.17x10^2 kg/m^3. The weight of the input piston is negligible. The radii of the input piston and output plunger are 8.56x10^-3 m and 0.171m, respectively. What input force F is needed to support the 27200-N combined weight of a car and the output plunger, when (a) the bottom surfaces of the piston and plunger are at the same level, and (b) the bottom surface of the output plunger is...

A hydraulic car lift has an input piston of radius 2.00 cm and negligible weight. The...

A hydraulic car lift has an input piston of radius 2.00 cm and negligible weight. The output piston has a radius of 79.2 cm, and the total load on the output plungers is 18000 N. If the car (output piston) needs to be lifted 1.70 m, what volume of non-compressible hydraulic fluid must be pumped into the system?
3 -1 POINTS OSUNIPHYS1 12.2.WA.018. MY NOTES | ASK YOUR TEACHER As shown in the figure...

3 -1 POINTS OSUNIPHYS1 12.2.WA.018. MY NOTES | ASK YOUR TEACHER As shown in the figure below, a uniform beam is supported by a cable at one end and the force of friction at the other end. The cable makes an angle of 30°, the length of the beam is L-1.75 m, the coefficient of static friction between the wall and the beam is 0.540, and the weight of the beam is represented by w. Determine the minimum distance x...
HWZ1 - Physics 2010, am My Notes +-12 points CJ10 11.P.039. The drawing shows a hydraulic...

HWZ1 - Physics 2010, am My Notes +-12 points CJ10 11.P.039. The drawing shows a hydraulic system used with disc brakes. The force F is applied perpendicularly to the brake pedal. The pedal rotates about the axis shown in the drawing and causes a force to be applied perpendicularly to the input piston (radius = 8.25 x 10m ) in the master cylinder. The resulting pressure is transmitted by the brake fluid to the output plungers (radil - 1.20 x...

10. + 0/3 points | Previous Answers SerPSET9 12.P.021. My Notes + Ask Your Teacher John...

10. + 0/3 points | Previous Answers SerPSET9 12.P.021. My Notes + Ask Your Teacher John is pushing his daughter Rachel in a wheelbarrow when it is stopped by a brick 8.00 cm high (see the figure below). The handles make an angle of a = 20.0° with the ground. Due to the weight of Rachel and the wheelbarrow, a downward force of 405 N is exerted at the center of the wheel, which has a radius of 15.0 cm....