Firstly sort the numbers in increasing order,
140,150,160,190,230,270,280,290,320,340,350,380,400,410,430,450,460,530,550,570,610,630,650,660,670,680,700,730,750,800,860,920,930,940,970,980,1000
There are total 37 numbers.
24th percentile means .24*37= 8.88 = 9th number in the sorted dataset
So the 9th number in the sorted dataset is 320.
So answer is P24= 320
nvar uzzes y open Math Assignments PRING 2019 > Assessment r2: Stem & Leaf, Histograms, Percentiles...
NG 2019> Assessment 2: Stem & Leaf, Histograms, Percentiles Due in 13 Ages Number of students 15-181 。 19-22 23-26 27-30 10 35-38 Find the relative frequency for the class with lower class limit 31 Relative Frequency Give your answer as a percent, rounded to two decimal places ersion Points possible: 1 This is attempt 1 of 3. Submit t/showtest.phplactionzskip&to 8
HW & Quizzes My Open Math Assignments ent Stem & Leaf, Histograms, Percentiles Due in 13 hours, 40 minutes. De The table below shows a stem-and-leaf diagram for the test scores of students in Liberal Arts Stems Leaves 49 349 345 7 03 10 1 How many students took the test? What is the lowest score on the test? What is the highest score on the test? The mean score on the test is: The midrange of test scores is:...
In C++ Programming: Using a single for loop, output the even numbers between 2 and 1004 (inclusive) that iterates (loops) exactly 502 times. The outputted numbers be aligned in a table with 10 numbers per row. Each column in the table should be 5 characters wide. Do not nest a loop inside of another loop. Hint: First create and test the code that output the numbers all on one line (the command line will automatically wrap the output to new...
Can somone show me how to do the 1st problem? Need to
find the LS and SS for the fit and the LH and SH for the hole.
Fits are all SHAFT BASIS METRIC but the shaft and hole diameters can not be used right out of the table. This is because the 3mm shaft tolerance does not match. You will need to lookup the "Fit" from the table, and then use the LS (Largest Shaft) and SS (Smallest Shaft)...
The Boeing 747 has a cruising altitude of 45,000 feet and
cruising speed of 275 m/s. At this elevation, the temperature and
pressure according to the US Standard Atmosphere (air properties as
a function of altitude) are 220K and 1.8x104 Pa, respectively. The
engines are steady state devices that can be modeled using the 1st
Law of Thermodynamics with air (ideal gas) as the working fluid
undergoing several processes.
a. The inlet area of the engines is 0.5 m2. What...
5) Evaluating Changes in Entropy for an Ideal Gas Air enters a turbine at 427 °C and 1 MPa and exits at 127 °C. The outlet pressure can be tuned by the operator in the range from 300 - 800 kPa. Determine the change in specific entropy of the air, se -si, as it flows through this turbine 3 ways a) Assuming constant specific heats. b) Integrating an appropriate formula from Table A-2(c) from the text, which gives a polynomial...
174 2 combustor , =1500 K Problem 2 (22 pts): Brayton cycle and entropy calculations An open Brayton cycle is used to generate electricity. Air enters the isentropic compressor at T1 = 300 K and P1 = 100 kPa with a mass flow rate m = 1.5 kg/s. The combustor can be modeled as a constant-pressure heat exchanger, supplying 1540 kW of thermal power to the air from a thermal reservoir (Th = 1750 K). Air enters the isentropic turbine...