20 points Endrin the following circuit. Suppose that Is, V, R and R2 are known.

Question

Question

Answer 1

Answer #1

from Circut diagram Ise Req=RHR2 Since Ri and Rr resistors are connected in series. ER ☆ from the can N=1 Ree 1 = Rey - Ritri

V2= (Vs/ R1+R2) R2

Rate it if u like

Answer 2

Similar Homework Help Questions

1002 1002 R + R3 100 2 R2 20 V 5 V Given the circuit in...

1002 1002 R + R3 100 2 R2 20 V 5 V Given the circuit in Figure above, Calculate the total current through R2, using the superposition method 83 mA 133 mA 0 67 mA 16 mA
lculate the total resistance of the following circuit where R,-20?, R,-30S2, and R 602 R2 R,...

lculate the total resistance of the following circuit where R,-20?, R,-30S2, and R 602 R2 R, Calculate the total resistance of the following circuit where R1-20 ?. R-30 ?, and Rs 602. 5, R3 6. What is the voltage across each resistor Ri 20 2 and R: 40 92 of the circuit below. The batt voltage is 6.0v R2
+O V w R. RB R2 R. + O Vaut R2 R3 Vre In the circuit...

+O V w R. RB R2 R. + O Vaut R2 R3 Vre In the circuit above, provided that: R1 5 kOhm R2 200 kOhm R3 R4 = 10 kOhm What is the total differential Gain of the circuit? +O V w R. RB R2 R. + O Vaut R2 R3 Vre In the circuit above, provided that: R1 5 kOhm R2 200 kOhm R3 R4 = 10 kOhm What is the total differential Gain of the circuit?

PI : For circuit below v-20 V and R,-8 Ohm and R2-2 Ohm. Calculate voltage and...

PI : For circuit below v-20 V and R,-8 Ohm and R2-2 Ohm. Calculate voltage and power loss in each resistor in the circuit. (Use voltage division and P = (voltage*voltage) resistance)- You cannot use KVL, KCL or Ohms law) Ri R2 P2: For circuit below i = 50 A and R1 = 15 Ohm and R2 = 10 Ohm. Calculate current and power loss in each resistor in the circuit. (Use current division and P - (current*current) resistance) You...
11 = 10 A R. = ? la = ? R2 = 40 V-= 20 V...

11 = 10 A R. = ? la = ? R2 = 40 V-= 20 V 1 = ? a) What is the resistance of R1? (2 marks) b) What is the current through R2? (2 marks) c) What is the current through the energy source? (2 marks) d) What is the total resistance in the circuit? (2 marks)
In the circuit shown below Vcc=5.0 V, R = 30 KO, R2 = 20 KO, RE...

In the circuit shown below Vcc=5.0 V, R = 30 KO, R2 = 20 KO, RE = 1.3 KO, RL = 2 KO, C1 = C2 = 10uF. For the BJT: B = 200, VA = 100 V, C = 1pF, C = 10pF, rx = 0, 9m = Ic/V1, V1 = 25mV. The internal resistance of source Vin is 1.0 KQ. For BJT: r. = VA/Ic, Im = B/gm. Av = -9m(R_Il ro), Miller Capacitances: Cm1 = C (1...

For the circuit in the figure above V-12 V.R, -50. R2-10 0.R - BOR-20. Rx -...

For the circuit in the figure above V-12 V.R, -50. R2-10 0.R - BOR-20. Rx - 30. R. - 7 and Ry 90. What are the currents through and potentials across each of the resistors TTTA 3120 * T... 13
30 points) Consider the circuit in Fig. 3, in which V, 48V, R -10k2, R2 =...

30 points) Consider the circuit in Fig. 3, in which V, 48V, R -10k2, R2 = 5K2 , R3 = 100K, and R4-50M. The Zener has a ½-3V and internal resistance Rz 100Ω . What is the output voltage over the load R1 for RL=100kΩ? R1 R3 Fig. 3
Consider a RC circuit with Vi 20 V, R, = 100 and R2 = 200 ....

Consider a RC circuit with Vi 20 V, R, = 100 and R2 = 200 . The capacitors are C, = 12 uF and C2 = 40 uF. The switch in the Figure 6(b) has been closed at position a for a long time. b а R Figure 6(b) What is the amount of electrical energy stored in the capacitor? (i) ANS: The switch is now flipped to position b and remains in position b for a long (ii) time....

10. For the circuit shown below, Ri=1002, R2=20 (2, R3=20 Q, R4=30 . What is the...

10. For the circuit shown below, Ri=1002, R2=20 (2, R3=20 Q, R4=30 . What is the equivalent resistance in the circuit shown in the figure? Find the current and potential across R4 and R2 when an 18 V battery is connected to this circuit. (10 points) R10 - 100 Rea 10+10+30 R = 102 R- 2003 R;=200 I am 30n R = 30 V =IR Reg = 502 I =ř Inlotions I.