Problem: A helical compression spring is made with music wire with wire diameter of 5 mm,...
1- A helical compression spring is to be made of oil-tempered wire of 4-mm diameter with a spring index of C = 10. The spring is to operate inside a hole, so buckling is not a problem and the ends can be left plain. The free length of the spring should be 80 mm. A force of 50 N should deflect the spring 15 mm. (a) Determine the spring rate. (b) Determine the minimum hole diameter for the spring to...
1- A helical compression spring is to be made of oil-tempered wire of 4-mm diameter with a spring index of C = 10. The spring is to operate inside a hole, so buckling is not a problem and the ends can be left plain. The free length of the spring should be 80 mm. A force of 50 N should deflect the spring 15 mm. (a) Determine the spring rate. (b) Determine the minimum hole diameter for the spring to...
1- A helical compression spring is to be made of oil-tempered wire of 4-mm diameter with a spring index of C = 10. The spring is to operate inside a hole, so buckling is not a problem and the ends can be left plain. The free length of the spring should be 80 mm. A force of 50 N should deflect the spring 15 mm. (a) Determine the spring rate. (b) Determine the minimum hole diameter for the spring to...
A helical compression srping is to be made of oil-tempered wire of 4 mm diameter with a spring index of C = 10. The spring is to operate inside a hole, so buckling is not a problem and the ends can be left plain. The free length of the spring should be 80 mm. A force of 50 N should deflect the spring 15 mm. Su = 1750 Mpa, allow for a 10% clash allowance and G = 79 GPa....
1) [60 pts] Helical Compression Spring A helical compression spring is wound using music wire of diameter, d, 2.64 mm. The spring has an outside diameter, OD, of 33 mm with plain ground ends and 14 coils. a) Estimate the spring rate. The spring rate is N/mm. b) What is the force needed to compress this spring to closure assuming that the spring will reach its shear strength at its solid length? The force needed to compress this spring to...
Problem. (20 points) A helical compression spring will be used in a pressure relief valve. When the valve is closed the spring leneth is 50 mm, and the spring force is to be 7 N. The spring uses a wire diameter of d 1.5 mm and a mean spring diameter of D = 10 mm, and has a solid length ofl.- 30 mm. Use hard-drawn ASTM A227 wire, squared and ground ends, and ignore buckling since the spring is in...
2. A helical compression spring is made from No. 8 steel wire and is to carry a 100 lb static load at a deflection of 1 inch. The outside coil diameter of the spring is 0.972 inches. The spring ends are squared. Assume the torsional yield strength of the wire is 80000 psi, and the shear modulus is 11.4 Mpsi, determine (a) The static load corresponding to the yield strength. (b) The deflection that would be caused by the load...
8. A helical compression spring is made of HD (A227) and has a spring constant of 4.25 lbs per inch. If the wire diameter is 0.1 inch and the coil mean diameter is 1.5 inch, what is the number of active coils: b) 9 a) 8 c) 10 d) 11 e) None of these 8. A helical compression spring is made of HD (A227) and has a spring constant of 4.25 lbs per inch. If the wire diameter is 0.1...
1. An existing helical-coil compression spring is wound from unpeened music wire with a diameter of d= 0.105". The mean diameter of the spring is D- 0.80" as shown. The applied load fluctuates between 0 and 25lb. A design life of 10 cycles is desired. We also know that 0.577Su for this music wire. Determine the existing factor of safety for this spring n2.0 (Hint: check both fatigue and yielding) D = 0.80 in
A compression spring has 20 coils with squared and ground ends, a free length of 1.25 in. and an outside diameter of 0.281 in. It is made of music wire with a diameter of .035 in. What is the spring rate (k) of the spring? What is the stress in the spring if compressed to solid height?