Problem # 1 A three-phase full converter controls the speed of a de motor. The motor's...
The speed of a separately excited de motor is controlled by a one-phase full-wave converter. The field circuit is also controlled by a full-wave converter and the field current is set to its maximum value. The AC supply voltage to the armature and field converters is one-phase, 400V, 50Hz. The armature resistance Ra 0.232, the field circuit resistance Rf- 1812, and the motor voltage constant is Kv 1.3V/A - rad/s. The armature current corresponding to the load demand Ia 42A...
A separately excited dc motor is fed by a 3-phase, 6-pulse converter shown in figure Q5. The 3-phase line is a 500 V, 60 Hz supply. At rated condition, the dc motor armature current is 15 A. The dc motor armature resistance is 0.15 Ω and the rated speed is 1700 rpm. If the delay angle of the converter is 36 °, calculate the following: 3-phase (2 0 line Figure Q5. (2 marks) Rated voltage of the motor a. b....
4. A 3-phase full-wave converter drive is feeding power to a 220 V, 20 A, 1000 rpm separately excited dc motor. The ac input to the converters are 415 V, 3-phase, 50 Hz, Y-connected supply system. The field is also controlled by a 3-phase full converter and is set to the maximum possible value. The armature resistance is 0.5 Q and the field resistance is 250 12. The motor voltage constant is 1.2 V/A rad/s. Assume continuous conduction and ripple...
i. The speed of a separately excited dc motor is controlled by a one-phase full-wave converter. The field circuit is also controlled by a full-wave converter, see V supply) Vs pk-150V Ra-0.310 L Rf 152O E-63V α. 1-35A Figure 3 The AC supply voltage to the armature and field converters is one-phase, 150Vpeak, 50Hz. The armature resistance Ra-0.31Ω, the field circuit resistance Rf-152Ω, and the motor voltage constant is Kv-1.3V/A. The armature current corresponding to the load demand la-35A The...
A. A three-phase ac induction motor drives a mechanical load. The motor's terminal voltage is 470V, 60 Hz. The motor's line current is 175 A, and the power factor is 0.85 lagging The motor's output power is 140 hp and the motor rotates at a speed of 1735 rpm. The motor's copper and core losses total 8.5 kW combined 1. Determine the number of poles of this motor 2. Determine the motor's shaft torque (N-m). 3. Determine the motor's rotational...
3. A 3-phase full-wave converter drive is feeding power to a 220 V, 20 A, 1500 rpm separately excited DC motor. The ac input to the converters are 415 V, 3-phase, 50 Hz, Y-connected supply system, connected through a step-down transformer so that the armature terminal voltage equals to rated voltage when converter firing angle is 0°. The resistance of the armature winding is 0.5 12. Determine the firing angle, i. when the motor is running at 1000 rpm and...
8) A three-phase thyristor controlled converter is used to drive a motor system. What is the required trigger delay angle a if the required average output DC voltage is 0.5Vm [2 points) a) 90 degrees. b) 45 degrees. c) 58.43 degrees. d) O degrees. 9) A 3-point motor starter arrangement is shown in the diagram below (1 point). Starting Resistence No volt col OFF Soft ron piece Starter handie Spring Over load release Lever Trangular iron Three Point Starter As...
If a manufacturer's specifications for a PM DC motor are as follows, what are the motor's no-load speed, stall current, starting torque, and maximum power for an applied voltage of 10 V? ■ Torque constant 0.12 Nm/A Electrical constant 12 V/1000 RPM Armature resistance-: 1.5 Ω
3. A controlled single-phase fiull-wave controlled rectifier is connected in a de motor drive in Figure 4. The de motor armature inductance can be assumed large enough such that any motor curent ripple is negligible. (a) Assuming negligible supply reactance, show that the average rectifier output voltage V, in tems of the supply ms voltage E and the firing angle a, is given by 2/2E (6 marks) cos a _ (b) Given that the supply voltage is 230V, 50HZ and...
A separately excited dc motor controlled by a 3 phase full wave fullcontrolled converter connected to the armature and field circuits. the acsupply voltage is 208v and the frequency is 60 Hz. If the field currentadjusted to If =1 A and the armature resistance Ra = 0.2 Ω ,the fieldresistance Rf = 250 Ω and the voltage constant K = 1.2V/A-rad/sec. The loadtorque TL=120 Nm and The firing angle of the armeture circuit adjusted tobe αa=30. Consider armature inductance La...