A helical extension spring has an end similar to that shown in Figure 1. The important...
Design an infinite-life helical coil extension spring with full end loops and generous loop-bend radii for a minimum load of 9 lbf and a maximum load of 18 lbf, with an accompanying stretch of in. The spring is for food-service equipment and must be stainless steel. The outside diameter of the coil cannot exceed 1 in, and the free length cannot exceed 21 in. Using a fatigue design factor of nf 2, complete the design. Use the Gerber criterion with...
Question 6 A composite spning has two close-coiled helical springs in series One spring is made of steel with a mean coil diameter of 15 mm, wire diameter 15 mm and has 10 coils The other spring is made from bronze with a mean coil diameter of 20 mm and wire diameter of 2 mm and B coils Calculate 61 The stiffness of the composite spring, 62 The greatest load that can be camned by the composite spring of the...
8. A helical compression spring is made of HD (A227) and has a spring constant of 4.25 lbs per inch. If the wire diameter is 0.1 inch and the coil mean diameter is 1.5 inch, what is the number of active coils: b) 9 a) 8 c) 10 d) 11 e) None of these 8. A helical compression spring is made of HD (A227) and has a spring constant of 4.25 lbs per inch. If the wire diameter is 0.1...
- USE ASTM A227 SPRING STEEL Design a helical compression spring for a static load of 470N at a deflection of 40mm with a safety factor of >2.6. The spring must fit within a 50mm hole using ASTM A227music wire. The cross sectional diameter must be rounded up to the nearest 0.5mm. The spring must sit flat in its assembled position. Specify all parameters necessary for manufacture of the spring. Number of turns, Nt- Free length, Lf - Outer Diameter,...
2. A helical compression spring is to be designed as shown in Fig Q2. The spring is required to exert a force of Po-102 N when compressed to a length of lo=44 mm. When its length is 1=76 mm, it must exert a force of P=22 N. The spring will be cycled rapidly, with severe service required. Use ASTM A401 steel wire. The factor of safety, η, need to be larger than 1.5. Starting with a spring index of 9,...
2. A helical compression spring is to be designed as shown in Fig Q2. The spring is required to exert a force of Po-102 N when compressed to a length of lo-44 mm. When its length is I-76 mm, it must exert a force of P-22 N. The spring will be cycled rapidly, with severe service required. Use ASTM A401 steel wire. The factor of safety, η, need to be larger than 1.5. Starting with a spring index of 9,...
2. A helical compression spring is to be designed as shown in Fig Q2. The spring is required to exert a force of Po-102 N when compressed to a length of lo-44 mm. When its length is I-76 mm, it must exert a force of P-22 N. The spring will be cycled rapidly, with severe service required. Use ASTM A401 steel wire. The factor of safety, η, need to be larger than 1.5. Starting with a spring index of 9,...
2. A helical compression spring is made from No. 8 steel wire and is to carry a 100 lb static load at a deflection of 1 inch. The outside coil diameter of the spring is 0.972 inches. The spring ends are squared. Assume the torsional yield strength of the wire is 80000 psi, and the shear modulus is 11.4 Mpsi, determine (a) The static load corresponding to the yield strength. (b) The deflection that would be caused by the load...
A close-coiled helical spring has a mean coil diameter 120 mm. A load of 4 kN causes a deflection of 50 mm and a maximum stress of 500 MPa. Calculate 4.1. a) The wire diameter b) The number of coils c) The energy absorbed when subjected to the maximum load d) The spring stiffness 4.2. By use of a clearly labelled neat sketch, show that the deflection in a close-coiled 12] where Wis ; where W is the axial load...
1. A closely coiled helical spring made of 15 mm diameter steel wire has 15 coils of 110 mm mean diameter. The spring is subjected to an axial load of 180 N. Calculate the maximum shear stress induced in the spring. Assume modulus of rigidity is 78 GPa. 2. A solid circular bar ABC consists of two segments, as shown in the figure. One segment has diameter d1= 65 mm and length L1 = 1.54 m; the other segment has...