Sec. A Sec. B Question 2. A 40 mm diameter shaft is made from carbon steel...
A shaft is to be manufactured from a steel having an ultimate tensile strength of 420 MPa, and a yield stress of 305 MPa. The shaft has a solid circular cross section of diameter 50 mm and is subjected to a sinusoidally varying torque ranging from 60 Nm to 130 Nm. It has also been established that the shaft has a fully-corrected endurance limit of 129 MPa and that a torsional fatigue stress concentration factor, kf = 2.1, exists at...
A ground steel shaft with a shoulder fillet has dimensions: D= 30 mm, d=25 mm and r= 2 mm. It is subjected to a combined nominal loading of 40 to 190 MPa bending stress and torsional stress of 20 to 70 MPa, which are in phase. Find the safety factor for infinite life if ultimate tensile strength is 965 MPa, state all assumptions.
A rotating shaft is made of 42 mm by 4 mm thick cold-drawn round steel tubing and has a 6 mm diameter hole drilled transversely through it. The shaft is subjected to a pulsating torque fluc- tuating from 20 to 160 Nm and a completely reversed bending moment of 200 Nm. The steel tubing has a minimum strength of Sut 410 MPa (60 ksi). The static stress-concentration factor for the hole is 2.4 for bending and 1.9 for torsion. The...
A low carbon steel shaft is designed to have a diameter of 30 mm. It is to be subjected to an axial load (P-30 kN), a moment (M-200 N-m), and a torque (T-300 N-m). Assume the yield stress for the steel is (280 MPa), the Poisson's ratio is (v= 0.29), and the safety factor is (1-1). Calculate the margin of safety using the following failure theories. a.) Rankine Criteria (Maximum Principal Stress) b.) Tresca Criteria (Maximum Shear Stress) c.) Saint...
for the shaft shown below answer thefollowing:1. Find the factor of safety in point H ifthe shaft is made from carbon steels1030 hot rolled and the shaftdiameter is 32 mm.2. Find the diameter of the shaft if itmade from wrought-aluminum alloy2024 heat treated and the factor ofsafety is 2.3. Select suitable carbon steel alloy forthat shaft if its diameter is 25 mmand factor of safety required is 1.5.
A stepped shaft with a ground finish is made of steel with an ultimate tensile strength of 1200 MPa. The shaft is loaded with a fully reversed torque of 20 Nm. Dimensions of the shaft are given below. (5) a) Given the stress concentration for fatigue loading, Kfs 1.3, find the location and magnitude of the maximum stress in the shaft. (14) b) Find the endurance limit, assuming room temperature and a reliability of 99%. (1) c)Will the part have...
QUESTION 1 The cross section of a key for a 41 mm diameter shaft. The Torque transmitted by shaft to hub is 636,348 N-mm. The key is made of steel having Syt - 380 MPa and the factor of safety is 2. Determine the length of the key (mm) in Shear.
Question 1: A rotating shaft with a diameter of 30 mm is made of 1018 cold-rolled steel. The stress concentration factor is 2.366, and the shear stress concentration factor is 1.75 respectively. The notch sensitivity is 0.78 and for shear it's 0.96 Estimate the factor of safety guarding against fatigue failure using modified-Goodman and Soder- berg for each of the following loading conditions: a) The shaft is subjected to a completely reversed torque of 120 N.m in phase with a...
A notched circular shaft shown is subjected to fully reversed bending. D=12.7mm, d=10.16 mm, and r=0.5mm. The steel material has the following mechanical and fatigue properties: yield strength (σ0)=1000 MPa, ultimate strength (σu)=1200 MPa, the fatigue strength coefficient (σf’)=1600 MPa, the fatigue strength exponent (b)=-0.1, and the fatigue limit (σe)=400 MPa. 5. (20 pts) A notched circular shaft shown is subjected to fully reversed bending. D-12.7mm, d-10.16 mm, and r-0.5mm. The steel material has the following mechanical and fatigue properties:...
Answer is 2.84 Question 1 A ships solid circular drive shaft is of diameter, d-54 mm, and is subjected to a torque, T steel with a yield stress of 350 MPa. 1700 Nm and an axial force, F-127 kN as shown. The shaft is made of Determine the Factor of Safety (accurate to two decimal places), according to Tresca's maximum shear stress failure theory. (Hint: Based on the state of stress in a surface element, consider Mohr's circle to get...