Homework Answers
apply I/io = e^-t/RC
i/i0 = (e^-(0.01/(369*0.215e-6)
i/i0 = 1.811 Amps
--------------------------------------------
apply impedence Z^2 = ( R^2+XL^2)
so R^2 = 55.1^2 -(26^2)
R^2 = 2360.61
R = 48.57 ohms
Add Answer to:
A capacitor is placed parallel across a resistive load in the circuit below. What fraction of...
A load impedance consists of 25 ohm resistance in series with 38 ohm inductive reactance. The...
A load impedance consists of 25 ohm resistance in series with 38 ohm inductive reactance. The load is connected across a 60 Hz, 240 V rms source. Use the voltage source as the reference (zero phase angle). a. Draw the circuit diagram. b. Calculate the value of inductance. c. Calculate the phasor value of current through the load impedance. d. Which leads, current or voltage? e. What is the phase angle between current and voltage? d. Calculate the phasor value...
1. What is the vacRMS Voltage for the signal shown below? 10 V 2 V 2....
1. What is the vacRMS Voltage for the signal shown below? 10 V 2 V 2. An AC voltage of 12vacaMs is equal to what peak to peak voltage? 3. In a purely resistive AC circuit where 10vacpK-PK is applied across an 8-ohm resistor, the current is 4. The total capacitance of a 330HF capacitor connected in parallel with a 470 uF capacitor is If an ac signal has a frequency of 125kHz, how much time does it take for...
X1 30 R-50 50 V X-30 0 Figure 13-2 21) If the resistance increases in Figure...
X1 30 R-50 50 V X-30 0 Figure 13-2 21) If the resistance increases in Figure 13-2, the bandwidth 22) What is the bandwidth of a resonant circuit if its resonant frequency is 14.2 MHz, the inductive reactance is 3.5 kQ and the coil's resistance is 8 ohm? 23) The output voltage of a circuit at 70.7 % of its maximum level measured in dB is: 24) Why does a resistive load increase the bandwidth of a given band-pass filter?...
An ac circuit with a 60 μF capacitor in series with a coil of resistance 18Ω...
An ac circuit with a 60 μF capacitor in series with a coil of resistance 18Ω and inductance 180mH is connected to a 100V, 100 Hz supply is shown below. Calculate inductive reactance capacitive reactance circuit impedance and phase angle θ circuit current I phasor voltages VR, VL, VC and VS resonance circuit frequency construct a fully labeled voltage phasor diagram
Make a sketch below of a balanced Y-connected resistive load, having a resistance of 300 S2 per p...
Please do draw the two circuit and calculate the
theoretical values.
Make a sketch below of a balanced Y-connected resistive load, having a resistance of 300 S2 per phase, connected to the power supply, with an ammeter connected in each line/phase, and a voltmeter across each phase. Knowing that Vi-1 is 208 V, determine the expected current- and volt-meter readins, and record these values in the table below. Please 3. use the actual components in the lab. Table 2 Y-connected...
An RLC circuit consists of an alternating voltage source with RMS voltage 90 V and frequency...
An RLC circuit consists of an alternating voltage source with RMS voltage 90 V and frequency 100 Hz, 180 ohm resistor, 200mH inductor, and a 900 micro-F capacitor, all wired in series. A) What is inductive reactance of the circuit? B) What is the capacitive reactance of the circuit?C) What is the impedance of the circuit? D)What is RMS current in the circuit?E) If the frequency is adjustable what frequency should you use to maximize the current in the circuit?
11. Which of the following describes what when the conjugate of the Thevenin impedance across its...
11. Which of the following describes what when the conjugate of the Thevenin impedance across its terminal that takes place when the impedance of the land is the pedance A. Maximum power will be delivered to the load B. The circuit will be capacitive. C. The circuit will appear resistive. D. A matching impedance must be placed in parallel 12. To ensure maximum power to maximum power to the load, which of the following is determined using the maximum power...
a load impedance described by 20+J12 ohm has 500Vrms applied across the load impedance. 1) draw...
a load impedance described by 20+J12 ohm has 500Vrms applied across the load impedance. 1) draw the circuit with resistor, inductor and capacitor components that has this load impedance with frequency of 100 Hz. 2) if the load is in a 3 phase power Y-Y configuration with line impedance of 1 ohm, determine: a) the line voltage at the load b) the phase voltage at the source
An RLC circuit consists of an alternating voltage source with RMS voltage 90 V and frequency 100 Hz
An RLC circuit consists of an alternating voltage source with RMS voltage 90 V and frequency 100 Hz, a 180 Ohm resistor a 200 ml inductor, and a 900 micro-F capacitor, all wired in series. a) What is the inductive reactance of the circuit? b) What is the capacitive reactance of the circuit? c) What is the Impedance of the circuit? d) What is the RMS current in the circuit? e) of the frequency is adjustable, what frequency should you use to maximize the current...
A series AC circuit contains a resistor, an inductor of 250 mH, a capacitor of 4.50...
A series AC circuit contains a resistor, an inductor of 250 mH, a capacitor of 4.50 uF, and a source with AV = 240 V operating at 50.0 Hz. The max maximum current in the circuit is 170 mA. (a) Calculate the inductive reactance. The inductive reactance depends on the value of the inductance and the frequency of the source. Q (b) Calculate the capacitive reactance. (c) Calculate the impedance. kn (d) Calculate the resistance in the circuit. kn. (e)...
1. What is the vacRMS Voltage for the signal shown below? 10 V 2 V 2. An AC voltage of 12vacaMs is equal to what peak to peak voltage? 3. In a purely resistive AC circuit where 10vacpK-PK is applied across an 8-ohm resistor, the current is 4. The total capacitance of a 330HF capacitor connected in parallel with a 470 uF capacitor is If an ac signal has a frequency of 125kHz, how much time does it take for...
X1 30 R-50 50 V X-30 0 Figure 13-2 21) If the resistance increases in Figure 13-2, the bandwidth 22) What is the bandwidth of a resonant circuit if its resonant frequency is 14.2 MHz, the inductive reactance is 3.5 kQ and the coil's resistance is 8 ohm? 23) The output voltage of a circuit at 70.7 % of its maximum level measured in dB is: 24) Why does a resistive load increase the bandwidth of a given band-pass filter?...
Please do draw the two circuit and calculate the
theoretical values.
Make a sketch below of a balanced Y-connected resistive load, having a resistance of 300 S2 per phase, connected to the power supply, with an ammeter connected in each line/phase, and a voltmeter across each phase. Knowing that Vi-1 is 208 V, determine the expected current- and volt-meter readins, and record these values in the table below. Please 3. use the actual components in the lab. Table 2 Y-connected...
11. Which of the following describes what when the conjugate of the Thevenin impedance across its terminal that takes place when the impedance of the land is the pedance A. Maximum power will be delivered to the load B. The circuit will be capacitive. C. The circuit will appear resistive. D. A matching impedance must be placed in parallel 12. To ensure maximum power to maximum power to the load, which of the following is determined using the maximum power...
A series AC circuit contains a resistor, an inductor of 250 mH, a capacitor of 4.50 uF, and a source with AV = 240 V operating at 50.0 Hz. The max maximum current in the circuit is 170 mA. (a) Calculate the inductive reactance. The inductive reactance depends on the value of the inductance and the frequency of the source. Q (b) Calculate the capacitive reactance. (c) Calculate the impedance. kn (d) Calculate the resistance in the circuit. kn. (e)...
Most questions answered within 3 hours.
-
Among 100 engineering students, 15 are chemical engineering
majors, 60 are undergraduates, and 5 are undergraduates...
asked 44 minutes ago -
On September 3, 2018, the Robers Company exchanged equipment
with Phifer Corporation. The facts of the...
asked 29 minutes ago -
Which one of the following statements about photophosphorylation
is false?
Question 3 options:
It can be...
asked 31 minutes ago -
In (Figure 1), the total resistance is 10.0 kΩ , and the
battery's emf is 22.0...
asked 45 minutes ago -
Prepare a series of 50 mL quinine standard solutions (10, 1.0,
0.10, 0.010, 0.0010μg/mL) by serial...
asked 47 minutes ago -
suppose a research organization conducts of annual expenditures.
The sampling bias of one sort or another...
asked 59 minutes ago -
A positive charge traveling along a magnetic field experiences
no magnetic force (True,False)
asked 1 hour ago -
Propose a mechanism for the photoreduction of acetaphenone. How
many products can be formed? Draw their...
asked 1 hour ago -
Fogerty Company makes two products—titanium Hubs and Sprockets.
Data regarding the two products follow:
Direct
Labor-Hours...
asked 1 hour ago -
The correct answer will be upvoted with positive feedback,
giving me incorrect answers will result in...
asked 1 hour ago -
Question:
Evaluation: Answer both (a) and (b): (a) Looking at
Table 6.1 in our text, explain...
asked 1 hour ago -
What is the maximum number of edges that a graph on 7 vertices can
have if...
asked 2 hours ago