What is the frequency ratio of output QC/CLK in the following circuit? The input of Flip-...
What is the frequency ratio of output QB/CLK in the following circuit? The input of Flip- Flops without connection are all "1". (Fig. 09) fo JA JB JC KO KI KI clk Fig. 9 QB/CLK= 1/6 A QB/CLK-1/5 B QB/CLK= 1/9 C. QB/CLK= 1/7 D.
A) Draw a frequency divider "divide by 2" and
"divide by 4" logic circuits as a single circuit utilizing JK
Flip-Flops. Indicate the input and output values on each
connection. Draw JK flip-flops as block
structures. Use rising edge triggering.
B) Draw your drawn JK Flip
Flop frequency divider circuit's outputs waveform to the
are below. Use rising edge triggering.
C) Draw a frequency divider "divide by 2" and
"divide by 4" logic circuits as a single circuit utilizing JK...
The sequential circuit shown below has two flip-flops A and B and one input x. It consists of a combinatorial logic connected to the flip-flops, as shown in the Figure 1. Below. Analyze the sequential circuit below: A J A' K Q lo B 2-to-1 MUX Y J Q 11 S B K CLK Figure 1a. Sequential Circuit a) Derive the next state equations for the sequential circuit above: find expressions for JA and KA and Jb and KB as...
Q D Clock Clk Q Clock Qb Q Qa Q Q Multiple type of flip-flops Circuit The figure above shows a circuit that use three different types of D flip-flops: a) D latch b) Rising-edge D flip-flop c) Falling-edge flip-flop For each one of the flip-flops enter their output for the times t1.t2.t3.t4 Assume that initially all outputs are '0' D
Study the following circuit and corresponding waveforms: a) D Q Clock CLK Q Undefined 01 02 Undefined Q Undefined Undefined Undefined Identify the waveforms that correspond to Qa, Qb and Qc. Provide the name of the components that produce Qa, Qb and Qc. (Note: one answer is none of the above.) (6 marks) b) Study the following circuit: D D D CLK CLK CLK CLK Explain why this will not implement a shift register. Your answer should include a waveform...
3. A timing diagram below shows a D Flip-flop and the input clock. Show the transition of the output Q at the positive transitions of the clock signal. Q 1 initially. Clk 4. Implement a 2-bit up-counter using D flip-flops. Show the circuit. 5. Implement a 2-bit down-counter using D flip-flops. Show the circuit. Transitions: 11->10->01->00->11->10->...
A sequential circuit with two flip flops, A and B; one input, x; and one output y, is specified by the following next-state and output equations. B(t+1)=Ax A(t+1)=A'B+Bx'+AB'x a) List the circuit state table and draw the corresponding state diagram. b) Draw the logic diagram of the circuit using only, one D-type and one T-type flip flops, one 2X4 decoder and one 2-input OR gate. The complement of the input variable, x is not available.
A sequential circuit with two flip flops, A and B; one input, x; and one output y, is specified by the following next-state and output equations: B(t+1) = AX A(t+1) = A’B + BX’ + AB’X y = A’X’ + B’ a) List the circuit state table and draw the corresponding state diagram b) Draw the logic diagram of the circuit using only, one D-type and one T-type flip flops, one 2X4 decoder and one 2-input OR gate. The complement of the input...
3. A sequential circuit has 2 JK flip-flops A and B and one input x. The circuit is described by the following flip-flop input equations: (a) Derive the state equations A(t1) and B(t +1) by substituting the input equations for the J and K variables (b) Draw the state diagram of the circuit (c) Design an equivalent circuit using D flip flops, i.e. a sequential circuit that uses D flip flops to implement the state diagram you obtained in part...
Draw(Design) a frequency divider by 10 circuit only using digital static circuits. but don't use any external RESET(CLEAR) signal to circuits. Circuits must have a one external Input(input clock). neglect output clock duty ratio, but 50% duty ratio is best. (a) Design using D-flip-flops (b) Design using JK-Flip-flops thanks you.