Question

Two parallel pumps are pumping water (p = 1000 kg/m) through very large diameter pipes of diameter D such that the friction l

0 0
Add a comment Improve this question Transcribed image text
Answer #1

A) K o Had 20 Given data Had 100M. 8=1000 neglur sp=sg Cot) Ap= looo *9.81 (100) 981810 pa Af = 988 kpa. equation for each peThe equation given opic3.57.10.99? +501.00 +981 spin kpa. (parabolic sin maisee a base borrable equation), sp dependent varia

Add a comment
Know the answer?
Add Answer to:
Two parallel pumps are pumping water (p = 1000 kg/m) through very large diameter pipes of...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • Use Newton-Raphson root-finding method to solve. A water-pumping system consists of two parallel pumps drawing water...

    Use Newton-Raphson root-finding method to solve. A water-pumping system consists of two parallel pumps drawing water from a lower reservoir and delivering it to another reservoir which is 40 m higher, as shown below. 40 m Pump 1: Ap = 810 – 25w, – 3.75wî (kPa) Pump 2: Ap = 900 – 65w, - 30wŹ (kPa) Pressure drop due to elevation can be written as Ap = 7.2w² + 392.28 (kPa) Also note that Wi + W2 = w (kg/s)...

  • Two identical pumps in parallel configuration will be used to draw water from Reservoir A (water...

    Two identical pumps in parallel configuration will be used to draw water from Reservoir A (water elevation 772') up to Reservoir B (water elevation -878'). The pipe will be 4,860 long, 2' diameter, with a Hazen-Williams coefficient of 100. Assume minor losses are negligible. The pump performance curve from thee manufacturer for one of these pumps is shown below. Determine the operation point for the two pumps in parallel by plotting below. Single pump 600 S00 400 Hp [ft] 300...

  • 1. You are designing a pumping station and have been asked to size and select a...

    1. You are designing a pumping station and have been asked to size and select a pump from 2 models. The system step is as follows: the discharge line is a 21-inch diameter PVC pipe with an assumed constant friction factor of f 0.014. The length of the piping is 2300 ft with an elevation gain of 40 ft and an exit loss (K-1.0).. The pump station is located near sea level and the temperature of the flow stream is...

  • A pump transports water from Tank 1 to Tank 2 through a constant-diameter piping system as...

    A pump transports water from Tank 1 to Tank 2 through a constant-diameter piping system as shown below (not to scale). The flow rate is controlled by two gate valves, the gate valve I controls the main pipeline, while the gate valve II controls the loop line from T-joint A to T-joint B. All pipes are galvanized steel pipe of diameter D = 4 in. It has a total length of Li2= 620 ft from tank 1 to tank 2....

  • 1/9 1 Piping system (14 points) Water is pumped from a reservoir to a large receiver...

    1/9 1 Piping system (14 points) Water is pumped from a reservoir to a large receiver vessel which is maintained at p4 6 bar (absolute) through the operation of the pump and a high pressure nitrogen supply that bleeds into the tank through a regulator. The water enters through an opening at the top of the vessel. A drain is provided at the low point in the system. Elevations are as shown. All valves are gate valves (k = 0.15)...

  • 1/9 1 Piping system (14 points) Water is pumped from a reservoir to a large receiver...

    1/9 1 Piping system (14 points) Water is pumped from a reservoir to a large receiver vessel which is maintained at p4 6 bar (absolute) through the operation of the pump and a high pressure nitrogen supply that bleeds into the tank through a regulator. The water enters through an opening at the top of the vessel. A drain is provided at the low point in the system. Elevations are as shown. All valves are gate valves (k = 0.15)...

  • (100 points) Water at 25°C is pumped at a rate of 0.075m's from a reservoir 20m above a pump to a free 1....

    (100 points) Water at 25°C is pumped at a rate of 0.075m's from a reservoir 20m above a pump to a free 1. discharge (this means discharged to atmosphere) 35m above the pump. The pressure on the intake side of the pump is 150kPa and the pressure on the discharge side of the pump is 450kPa. The pipe between the reservoir and the pump is 3 meters of Sin diameter cast iron. From the pump to the discharge the pipe...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT