1. Find Vo in the circuit below. Show the work clearly (No credit without detailed procedure)....
(pts. 10) a) Calculate vo in the circuit below. 10 ΚΩ 8 ΚΩ 3V 5V οι α + ο (pts, 10) #1(b) Find the w of following opamp circuit. 20 ΚΩ -0.2V 10 ΚΩ -- 40 ΚΩ 0.4V 10 ΚΩ 5 ΚΩ
(10 Points) Find Vo and io for the circuit shown below. 4 ΚΩ 8 ΚΩ + II 12V ( 2vΟ) 20 kΩξυο
(1) Use the step-by-step method to find Vo(t) for t>O in the circuit shown below. 4 ΚΩ 4 ΚΩ 200 μF ΑΛΛΑ 24 VB X, ο 34 ΚΩ 2 ΚΩ Bo(1)
a) Use MultiSim to find Vo in the circuit below. Paste your Multisim circuit showing the value of Vo in the space below. b) Use mesh analysis to solve the same problem by hand. Show your work in the space below. Compare the Multisim answer to that obtained by hand. Are they the same? 5 A 2Ω 20 V 412 40 V (+ V: 27.1 V V(PP): 2.07 pv V(rms): 0Vv V(dc): 27.1V V(freq): 5A R2 R3 PR1 R1 2Ω...
This is a multi part problem. Please answer each part correctly with work for thumbs up! Thanks! Part 1 Determine the value of V, in the network in the figure. Ο + 93 ΚΩ 59 ΚΩ 1 ΚΩ 21 ΚΩs ξ 58 ΚΩ V, 17ν Ενα First let's perform a delta to wye transformation. Using this new drawing, find: R1, R2, R3, R4, R5. R, Io Ο + Ra} ξ Rς και m 1. O + R33 3R5 Vo (...
find the current, including its direction, through the 20 ohm resistor. please show all work Circuit 2 Answer the following questions for the circuit shown below. Pay attention to the orientation of the power supplies. 15 2 102 w +6V 202 52 +3V
for this circuit shown find the equivalent (total) resistance. show the work and assume all numbers are given to 2 significant digits Rychme Ry Some Rohms 15 ohm Rg 20 mg d) 1Ω 2Ω 1Ω Λ 12Ω 4Ω. 10Ω 8Ω
Problem # 2: For the each circuit show n below find : a) and b) ω1 and ω2 c) Band Q 300 Ω V(t) : 40 μΗ 25 nF Vo(t) Fig (a) 1.25 pF 12.5 ΚΩ 312.5 mH V(t) 50ΚΩ Vo(t) Fig (b)
Show all work. Answers without clear explanation or derivation will receive no credit. I. (10) A block of wood is projected up an incline plane with initial speed vo-10m/s. The inclination of the plane is 30° and the coefficient of sliding friction is u 0.1. Find the total time for the block to return to the point of projection. Note: Make sure to clearly draw the free body diagrams for the motion up the plane and for the motion down...
Problem No. 1 For the circuit shown below: (a) Turn off the AC source and find the current and voltages of the diodes. State which one is on or off. (b) Turn off the dc sources and draw the small signal equivalent circuit and find voli "Sov OVO D D2 KSR For the circuit given below, +10 V 1. Find the input resistance 2. Find the output resistance. 3. State the type of the amplifier (CE,CB,CC) Ca → WA Rs...