Homework Answers
Add Answer to:
solve both parts a and b please
A centrifugal pump having a head capacity relationship given...
You have to do Problem 3, while using the diagram in problem 2 as reference. Problem#3:...
You have to do Problem 3, while using the diagram in problem 2
as reference.
Problem#3: If the elevation change in the above Pb#3 is 150 ft, what would be the flow rate with the given pump? What would be the flow rate if two of the same pumps are used in series instead of one? (Assume that the friction factor is the same 0.02 for the purpose of calculations although it does vary). Appx Ans: 175 gpm, 440 gpm....
A centrifugal pump test yields the following data: Pump Head Flow (m)(L/min) 30 25 20 40 The pump...
A centrifugal pump test yields the following data: Pump Head Flow (m)(L/min) 30 25 20 40 The pump curve can be approximated by a parabola. This pump draws water from a large reservoir. The discharge of the pump feeds 150 m of 1.5 cm inside diameter pipe and then 225 m of 3 cm inside diameter pipe.. The two pipes both have a roughness of 0.5 mm The 3 cm pipe discharges to atmosphere a distance 40 m below the...
1. A centrifugal pump performance data are shown in the following table for water. Pump speed-250...
Mechanical Lab II. Please answer asap with clear work. Thank
you!
1. A centrifugal pump performance data are shown in the following table for water. Pump speed-2500 RPM Pa or P2 (bar) P. or Pi (bar) Volume of water(L Time (sec) Input-Power (W) -0.3 20 60 100 For this data set, calculate the following i. Pump discharge capacity Q (LUs and GPM) ii. Pump head H (m and ft) iii. Fluid power Pr (Watt) iv. Brake power Pb (Watt) v....
Please answer question 7: A centrifugal pump discharges 500 GPM through a 12-inch diameter impeller. The fluid...
Please answer question 7:
A centrifugal pump discharges 500 GPM through a 12-inch diameter
impeller. The fluid leaves the impeller with a
tangential velocity of 17 ft/sec. If water, @ 68°F,
enters the impeller via radial flow (I.E. no whirl), and the inner
radius and thickness of the impeller are
1.75-inches. (Assume a constant thickness of the
impeller) and if the pump speed is 1775 rpm, with a head loss of
4.5-feet. What is the horsepower input to the flow by
the pump?
QUESTION...
A centrifugal pump is used to pump water at 77ºF from a reservoir whose surface is 20 ft above th...
A centrifugal pump is used to pump water at 77ºF from a reservoir whose surface is 20 ft above the centerline of the pump inlet. The Pipe System consists of 67.5 ft of PVC pipe with a 1.2 in ID and negligible average internal roughness height. The length of the pipe from the bottom of the lower tank to the pump inlet is 12 ft. There are several minor losses in the pipe: an acute edge entry (KL = 0.5),...
You own a centrifugal pump that is 7 inches in diameter and is known to have...
You own a centrifugal pump that is 7 inches in diameter and is known to have a maximum efficiency of 84% at a flow rate of 300 GPM and a head of 75 ft., and it runs at 1200 RPM. You have an old case from another pump that is geometrically similar to the existing pump, and it is made to handle an impeller with a diameter of 8 to 12 inches. You decide to make a 10 inch diameter...
02. centrifugal pump draws benzene at 25°C (sp. weight of benzene 8.59 kN/m) om a tank whose level is 2.6 m below the pump inlet. The atmospheric pressure (abs). The head loss in the suction pipi...
02. centrifugal pump draws benzene at 25°C (sp. weight of benzene 8.59 kN/m) om a tank whose level is 2.6 m below the pump inlet. The atmospheric pressure (abs). The head loss in the suction piping due to friction and minor osses is 0.8 N.m /N. The vapor pressure of benzene is 13.3 kPa (abs). Determine he available net positive suction head (NPSH) and tell f it is acceptable or not. (10 points) Discharge ine Flew 2.6 m What is...
3. A centrifugal pump performance data are shown in the following table for water. Pump speed...
3. A centrifugal pump performance data are shown in the following table for water. Pump speed 2500 RPM Pe or P2 (bar) P or Pi (bar) Volume of water (L) Time (sec) Input-Power (W -0.3 20 60 100 For this data set, calculate the following: i. Pump discharge capacity Q (L/s and GPM) ii. Pump head H (m and f) iii. Fluid power Pr(Watt) iv. Brake power Pb (Watt) v. Pump overall efficiency η (%) vi. Flow rate coefficient Ca...
mately 100 n+0.00 Water must be pumped through a pipe network that has a requaired head of approx where Q has units of gpm An engineer is considering using a centrifugal pump operating at 1 ugal p...
mately 100 n+0.00 Water must be pumped through a pipe network that has a requaired head of approx where Q has units of gpm An engineer is considering using a centrifugal pump operating at 1 ugal pump operating at 11s0 rpm with three possible impeler diameters: 6·T, and ir A) If at least 160 gpm of flow is needed, which (if any) of the impellers will meet this n 8) Estimate the pump efficiency and motor power for the 6...
4.45 A two-tank pump/pipe system has a head requirement of 23.4 ft at a flow rate of 100 gpm. The...
4.45 A two-tank pump/pipe system has a head requirement of 23.4 ft at a flow rate of 100 gpm. The elevation difference between the fluid surfaces in the tanks is 10 ft. The pump is a Bell & Gossett Series e-80 Model 2.5x2.5x9C operating at 1170 rpm with a 7.5-inch impeller. a. Develop an cquation for the system curve. b. Use a computer program to develop an equation for the 7.5-inch impeller using data read from the pump performance curve...
You have to do Problem 3, while using the diagram in problem 2
as reference.
Problem#3: If the elevation change in the above Pb#3 is 150 ft, what would be the flow rate with the given pump? What would be the flow rate if two of the same pumps are used in series instead of one? (Assume that the friction factor is the same 0.02 for the purpose of calculations although it does vary). Appx Ans: 175 gpm, 440 gpm....
A centrifugal pump test yields the following data: Pump Head Flow (m)(L/min) 30 25 20 40 The pump curve can be approximated by a parabola. This pump draws water from a large reservoir. The discharge of the pump feeds 150 m of 1.5 cm inside diameter pipe and then 225 m of 3 cm inside diameter pipe.. The two pipes both have a roughness of 0.5 mm The 3 cm pipe discharges to atmosphere a distance 40 m below the...
Mechanical Lab II. Please answer asap with clear work. Thank
you!
1. A centrifugal pump performance data are shown in the following table for water. Pump speed-2500 RPM Pa or P2 (bar) P. or Pi (bar) Volume of water(L Time (sec) Input-Power (W) -0.3 20 60 100 For this data set, calculate the following i. Pump discharge capacity Q (LUs and GPM) ii. Pump head H (m and ft) iii. Fluid power Pr (Watt) iv. Brake power Pb (Watt) v....
Please answer question 7:
A centrifugal pump discharges 500 GPM through a 12-inch diameter
impeller. The fluid leaves the impeller with a
tangential velocity of 17 ft/sec. If water, @ 68°F,
enters the impeller via radial flow (I.E. no whirl), and the inner
radius and thickness of the impeller are
1.75-inches. (Assume a constant thickness of the
impeller) and if the pump speed is 1775 rpm, with a head loss of
4.5-feet. What is the horsepower input to the flow by
the pump?
QUESTION...
You own a centrifugal pump that is 7 inches in diameter and is known to have a maximum efficiency of 84% at a flow rate of 300 GPM and a head of 75 ft., and it runs at 1200 RPM. You have an old case from another pump that is geometrically similar to the existing pump, and it is made to handle an impeller with a diameter of 8 to 12 inches. You decide to make a 10 inch diameter...
02. centrifugal pump draws benzene at 25°C (sp. weight of benzene 8.59 kN/m) om a tank whose level is 2.6 m below the pump inlet. The atmospheric pressure (abs). The head loss in the suction piping due to friction and minor osses is 0.8 N.m /N. The vapor pressure of benzene is 13.3 kPa (abs). Determine he available net positive suction head (NPSH) and tell f it is acceptable or not. (10 points) Discharge ine Flew 2.6 m What is...
3. A centrifugal pump performance data are shown in the following table for water. Pump speed 2500 RPM Pe or P2 (bar) P or Pi (bar) Volume of water (L) Time (sec) Input-Power (W -0.3 20 60 100 For this data set, calculate the following: i. Pump discharge capacity Q (L/s and GPM) ii. Pump head H (m and f) iii. Fluid power Pr(Watt) iv. Brake power Pb (Watt) v. Pump overall efficiency η (%) vi. Flow rate coefficient Ca...
mately 100 n+0.00 Water must be pumped through a pipe network that has a requaired head of approx where Q has units of gpm An engineer is considering using a centrifugal pump operating at 1 ugal pump operating at 11s0 rpm with three possible impeler diameters: 6·T, and ir A) If at least 160 gpm of flow is needed, which (if any) of the impellers will meet this n 8) Estimate the pump efficiency and motor power for the 6...
4.45 A two-tank pump/pipe system has a head requirement of 23.4 ft at a flow rate of 100 gpm. The elevation difference between the fluid surfaces in the tanks is 10 ft. The pump is a Bell & Gossett Series e-80 Model 2.5x2.5x9C operating at 1170 rpm with a 7.5-inch impeller. a. Develop an cquation for the system curve. b. Use a computer program to develop an equation for the 7.5-inch impeller using data read from the pump performance curve...
Most questions answered within 3 hours.
-
Assume Kw = 1.01 ✕ 10−14
For pure water, we can calculate [H3O+ ] = [OH...
asked 7 minutes ago -
Suppose that on a temperature scale X, water boils at 203.0°X
and freezes at -105.7°X. What...
asked 57 minutes ago -
BaS crystallizes in a cubic unit cell with S2- ions on each
corner and each face....
asked 1 hour ago -
A. 0≤P(Oi)≤10≤P(Oi)≤1 for each i
B. P(Oi)≤0P(Oi)≤0
C. P(Oi)=1+P(OCi)P(Oi)=1+P(OiC)
D. P(Oi)≥1P(Oi)≥1
If an experiment consists of...
asked 3 hours ago -
A battery has an emf of 9.20V and an internal resistance of 1.20
ohm. a)What resistance...
asked 2 hours ago -
The area of an elastic circular loop decreases at a constant
rate, dA/dt = −6.60×10−3 m2/s...
asked 4 hours ago -
The denaturation of proteins can be described by the
equilibrium
F⇌U
where F and U represent...
asked 5 hours ago -
Please answer what the maximum and minimum force is, and the
angle on the ion is...
asked 5 hours ago -
implement a program that reads a number of rows and a symbol.
The program will draw...
asked 5 hours ago -
Assume that when adults with smartphones are randomly selected,
45% use them in meetings or classes....
asked 5 hours ago -
Determine the number of formula units of
Na2SO4 and moles of oxygen contained in 8.11
moles...
asked 5 hours ago -
Explain in steps on the following code
What would be the output when executed
using System;...
asked 6 hours ago