1. An FCC aluminum polycrystal with 12 slip systems is loaded in tension. (hint: you have to figure out local direction of each grain to get loading direction that is shown as arrow)
a) Which grain will yield first when it is loaded in vertical direction figure 1a?
b) Which grain will yield first when it is loaded in horizontal direction figure 1b?
1. An FCC aluminum polycrystal with 12 slip systems is loaded in tension. (hint: you have...
5. A cubic close-packed (FCC) metal is deformed under tension. The tensile axis lies along [2 -3 1] A. What is the primary slip system? [0-1 --1), [01 1 (1- 1), [-1 0] (1 1 -1), [1 101 (1 -1 1) B. Determine cross slip and co-planar slip systems for that system. C. IF the critical resolved shear stress of that slip system was equal to 2 MPa, calculate the applied stress required to start plastic deformation in the material...
how
do you fill out the table?
Step 2: BCC Single Crystal For a BCC single crystal, thOnsile direction is along [123]. (1) Calculate the Schmid factors for all slip systems in Table 1 below. (2) Which slip system will be activated first, as the tensile load gradually increases? Tip: you may want to use a computer program such as Excel to facilitate the calculation. cos Schmid factor Slip first? Slip Systems cos (011)[111] (011)[111] 0.9449 (011)[111] (011)[111] (101)[111] (101)[111]...
1. State the difference between I and polycrystalline materials. Deformability of BCC and FCC metals. Strength and UTS of metals. 2. Determine the slip systems in BCC and FCC materials. Show the calculations that support your determinations. 3. Find the indices that represent the planes in the following cubic unit cell and show the X-Ray diffract-ability of the these planes in FCC and BCC structures: 4. A tensile specimen with a 12 mm initial diameter and 50 mm gauge length...
Problem 1 (10 pts) It is required to manufacture a 2.5 mm diameter copper rod from larger diameter stock by drawing. The rod should have a tensile strength of 300 MPa or more, a yield strength of 200 MPa or more, and ductility of 10% or more. Determine (a) the range of%CW which will allow achieving those properties, and (b) within this range clearly pick a certain%CW and determine the corresponding diameter of the starting stock. yield strength (MPa) tensile...
12. A longitudinal standing wave can be created in a long, thin aluminum rod by stroking the rod with very dry fingers. This is often done as a physics demonstration, creating a high-pitched, very annoying whine. From a wave perspective, the standing wave is equivalent to a sound standing wave in an open-open tube. In particular, both ends of the rod are anti-nodes. What is the fundamental frequency of a 2.50 m -long aluminum rod? The speed of sound in...
question 4-7
4. Travelling Waves and Their Characteristics A rope wave travels in the positive x -direction. You are also told that the speed of the wave is 1000 cm/s, its frequency is 200 Hz, and that the wave is subject to the following initial conditions: at x 0 and t = 0: y =-1 cm, and, at x = 0 and t : ar = +20 cm/s (this is the velocity of the point on the rope at horizontal...
I need help to write a nice introduction for experiment 6
please ( no hands write ) typing
Thank you
HEAT TREATMENT OF STEELS EXPERIMENT 6 EXPERIMENT 6 HEAT TREATMENT OF STEELS THEORY The Effect of Cooling Rate One of the most convenient methods for controlling the properties of a given steel, i.e., a steel whose composition is already fixed, consists of austenizing the steel and ten cooling to room temperature at some predetermined rate. A variation of cooling rates...
need solution for milestones A Q1
Solid Mechanics 3 Assessment Task 1a - 2020 Milestone a Question 1. For each of the plane-stress conditions given below, construct a Mohr's circle of stress, find the principal stresses and the orientation of the principal axes relative to the xy axes and determine the stresses on an element, rotated in the x-y plane 60° counterclockwise from its original position: (a) dx = 200 MPa Oy - 300 MPa T .40 MPa (b) dx...
Game Description: Most of you have played a very interesting game “Snake” on your old Nokia phones (Black & White). Now it is your time to create it with more interesting colors and features. When the game is started a snake is controlled by up, down, left and right keys to eat food which appears on random locations. By eating food snake’s length increases one unit and player’s score increases by 5 points. Food disappears after 15 seconds and appears...
The following guidelines outline the basic template for a robot vacuum cleaner game. The game must be implemented in c programming language. It mimics a robotic vacuum cleaner. The code must only use the following libraries: #include <math.h> #include <stdlib.h> #include <string.h> #include <limits.h> and any .graphics and .timers libraries. The guidelines are outlined as follows: Terminal Set-up: you may assume that the terminal will be quite large, for example, on the order of 150×50, or more. Status Display: The...