ALL 6 forces that act on the bolt are equal in magnitude. All 6 forces are applied at the same time. If d=0.3 [m] and F1=F2=F3=F4=F5=F6=50[N], what is the torque around the center of the hexagonal bolt? You may use the diagram below.
A wrench is used to apply a torque on a bolt as in the picture below....
. All forces shown on diagram are in lb. Remember that your final answers shall have units, i.e. lb. Solution can be solved using software, no hand calculation needed. . The column vector {x} will be as follows {x} = [F1 F2 F3 F4 F5 F6 F7 V3 H5 V5]T 400 200 F1 F7 FS F4 F2 45° 60 3 30 F6 F3 400 200 F1 F7 FS F4 F2 45° 60 3 30 F6 F3
Consider a right triangle of mass 6.69 kg and sides a=2.1 m and b, shown in the picture below. The triangle is pivoted at the corner at the top, as shown, with four forces , F1=16 N, F2=16 N, F3=15 N, and F4=15 N acting on it. The angle a=27 degrees. What is the z-component of the torque exerted on the triangle by force F1? у Axis of rotation х FA a F1 a 90° a b α F2 F3
Use the standard conventions of up being the ty direction, right being the +x direction, and counterclockwise as being the positive rotational direction. Five forces act on a thin rod of mass 12kg and length 1m as shown. All five foreacha magnitude. The center of mass of the rod is shown as a dot, and the axis of rotation is an X 1) Which of the forces exert zero torque about the axis shown? a) F b) F3 c) F2,...
The preloads of the M10 bolts used in a pressure vessel are applied with the wrench shown. For the 16,500 N preload force, Fi, the required torque, T, is approximated as T=K*Fi*d where K-0.20 and d is the nominal bolt diameter. The required torque is developed by applying a force to the end of the wrench as shown. The wrench material is AISI 1035 steel, forged and heat treated. For the applied force, determine the critical failure spot for yielding...
Number 7 only please Three forces act on the anchor bolt connection shown below. The forces are concurrent at point A.Express all answers to three significant figures with the appropriate units. F2 35 kN FI F3 = 10 kN Express force F1 in rectangular vector form. Take F: = 20 kN and 6, = 50.. Problem #2 Express force F2 in rectangular vector form. Problem#3 Express force F, in rectangular vector form. Problem#4 Determine the resultant force FR in rectangular...
1. Two forces, F1 and F2, are pulling on an eye bolt at point A in the picture below a. Determine the coordinates of point C. b. Determine the position vector rac, the magnitude of the position vector, TraclTac; the unit vector uaci and finally the force vector, c. Determine the position vector rab the magnitude of the position vector, Trabl Tab; the unit vector lab; and finally the force vector, F2. d. Determine the resultant force vector, FR -...
Three forces act on the anchor bolt connection shown below. The forces are concurrent at point A. Express all answers to three significant figures with the appropriate units.Problem #1 Express force F1 in rectangular vector form. Take F1=20 kN and θ1=50°. Problem #2 Express force F2 in rectangular vector form. Problem #3 Express force F3 in rectangular vector form. Problem #4 Determine the resultant force FR in rectangular vector form. Take F1=20 kN and θ1=50°. Problem #5 Determine the magnitude Fe of the resultant force. Take F1=20 kN and...
Three forces are exerted on the disk shown in the figure below, and their magnitudes are F3 = 2F2 = 2F1. The disk's outer rim has radius R, and the inner rim has radius R/2. As shown in the figure, Fi and F3 are tangent to the outer rim of the disk, and $2 is tangent to the inner rim. F3 is parallel to the x axis, F2 is parallel to the y axis, and F1 makes a 45° angle...
Given is a historical time series for job services demand in the prior 6 months. Month Demand 1 817 2 736 3 816 4 718 5 805 6 785 Use the table below to answer all questions: Month Demand Forecast 1 817 F1 2 736 F2 3 816 F3 4 718 F4 5 805 F5 6 785 F6 7 F7 If the demands forecast is Not Possible (NP) to generate for a particular month, then you must type in NP...
The 100[N] pole below is non uniform. It is leaning on a pipe on the right and the floor on the left. The center of mass of that pole is at point C. Draw a rigid body diagram for the pole Fill the table below What is the Normal (upwards) force by the floor on the pole? lul --1.5m- 2.5m 42° Force/Torque Table: Forces x у TA Net