And p1= 3.46MPa
https://neutrium.net/fluid-flow/pressure-loss-from-fittings-excess-head-k-method/
Thank you ??
this is all of the information given Problem 3. A piping system consists of 1200 m...
3) The system in Figure below consists of 1200 m of 5 cm cast-iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water at 20°C into the reservoir? (For water at 20°C, take p-998 kg/m3 and u-0.001 kg/m-s. For cast iron, take ε 0.26...
Problem 5: The system in the Figure consists of 1200 m of 5 cm cast-iron pipe, two 45o and four 90 flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water at 20°C into the reservoir? Elevation 500 m Sharp exit 45° Open globe 45 Problem 5: The system in the...
The system shown in the diagram consists of 1200m of cast-iron pipe with an internal diameter of 5cm (roughness of 0.00015 ft), two 45o and four 90o long radius elbows, a fully open bevel seat globe valve, and a sharp exit into a reservoir. If the elevation difference between the inlet and level in the reservoir is 10m, what gauge pressure is required at point 1 to deliver 0.005m^3/s of water at 20oC into the reservoir (use density of 998.2...
Water (p=998kg/m^3, u=0.001Pa*s) flows from reservoir A to reservoir B through the piping system shown. Each elbow has a minor loss coefficient of 1.2. Each valve has a minor loss coefficient of 3.2. The entrance and exit are both sharp edged. Determine the flow rate L/min. You now need to modify the piping system to increase the flow rate to 100L/min by reducing the length of the 25mm pipe. What must new length of the 25mm pipe be? 86. Water...
In the given figure, the pipe entrance is sharp-edged. The elevation at the entrance is Az 44 m. If the flow rate is 0.004 m3/s, what power in Wis extracted by the turbine? For water at 20 "C, take p 998 kg/m3 and ? 0.001 kgm s. For cast on take ? ~ 0.26 mm. The minor loss coefficients are Entrance: 0.5; 5-cm 2 open globe valve: K-6.9 Take ?-227 For the given flow. take f 0.0316. Round the answer...
Two water reservoirs A and B are connected to each other through a 35m-long, 2-cm-diameter cast iron pipe with a sharp-edged entrance. The pipe also involves a swing check valve and a fully open gate valve. The water level in both reservoirs is the same, but reservoir A is pressurized by compressed air while reservoir B is open to the atmosphere at 94 kPa. If the initial flow rate through the pipe is 1.2 L/s, determine the air pressure (gage)...
Water at 70°F flows by gravity from a large reservoir at a high elevation to a smaller one through a 60-ft-long, 2-in-diameter cast iron piping system that includes four standard flanged elbows, a well-rounded entrance, a sharp-edge exit and a fully open gate value. Take the free surface of the lower reservoir as the reference level and the elevation of the higher reservoir is 12.5 ft. a) Make a schematic of the problem b) Determine the flow rate (ft/min)
2) In the Figure below, the pipe entrance is sharp-edged. If the flow rate is 0.004 m3/s, what power, in W, is extracted by the turbine? (For water at 20°C, take ρ-998 kg/m3 and μ 0.001 kg/ms. For cast iron, take ε ~ 0.26 mm) Open globe valve Turbine 40 m Water Cast iron: L 125 m, D 5 cm
The total length of the piping system made of cast iron providing hot water to a house is considered to have a 42m length with a constant diameter. The entrance gage pressure is 85 kPa and exit at 15 kPa gaged. Consider the water density equal 980 Kg/m' and the viscosity 1.138x10 Kg/ms. a) Compute the piping system diameter if the volumetric flow rate provided by this system is equal to 0.1 L/s. There is no pump present in this...
2. Water flows at a rate of 60 L/s from a main reservoir to a subsidiary through a 600 m long, 185 mm diameter asphalted cast iron pipe as shown in the figure. The pipeline contains a gate valve, a globe valve and 4 standard 90° elbows. The entrance and exit are square edged, and all fittings are screwed ends, determine, You need Kinematic viscosity of water, 1 x 10-6 m/s2 (a) The friction head loss in the pipe, (b)...