They asked for diameter of brass portion.
The answer is 42.695 mm or 0.042695m
Steps are given in the attached picture
A rod is made from two segments: AB is steel and BC is brass. It is...
3. A rod is made from two segments: AB is steel and BC is brass. It is fixed at its ends and subjected to two torques as shown in the figure. The steel portion has a diameter of dAN-30mm. The brass portion a diameter of dac-60mm. GAB-75GPa, GBC-37.5GPa. (1) Determine the support reaction at A and C. (2) Draw the stress distribution on a volume element at point E. (You don't need to know between D and E. The location...
Problem 5.88 A rod is made from two segments AB is steel and BC s brass. It is foxed at its ends and subjected to a torque of T 680 N-m Ga 75 GPa G 39 GPa (Figure 1) Part A Express your answer to three significant figures and include the appropriate units 因 Figure 1 of 1 ? d Value Units 60 m N-m Provide Feedback .75 m
A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (E, -200 GPa 17 c)and portion BC is made of brass (E,-105 GPa, b-20.9 x 10-6/C) Knowing that the rod is initially unstressed, determine the compressive force induced inABC when there is a temperature rise of 53 °C 30-mm diameter 200 mm 56-mm diameter 380 mm
A rod consist of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel with the following properties (Es 200 GPa, as 11.7 x 10 6/C) and portion BC is made of brass with the following properties (E, 105 GPa, a 20.9 x 10 6/°C). Determine the compressive force induced in ABC when there is a temperature rise of 50°C, knowing that the rod is initially unstressed 2. 30-mm diameter 250 mm
CE 3350 Summer 2019 EXAM 2 NAME Mohama Alhemian Closed book, closed notes, closed hon sheet only formulas are allowed; you collected with the exam. You may us lowed; you cannot write One 8 " by 11" formula sheet is allowed. On the formul Write definitions or sample problems. Formula sheet will b blator. You cannot use a cell phone. 1. (35 points) Given: A rod is made from two segments. torque of 700 N.m. The steel portion has a...
3. A rod consisting of two cylindrical portions AB and BC is restrained at both ends, as shown in figure Q3 below. Portion AB is made of brass (E 105 Gpa, and ь-20.9 x 10-6 per °C) and portion BC is made out of aluminum (Eb 72 Gpa, and otb 23.9 x 106 per °C). The rod is initially unstressed at room temperature of 20 °C. If the temperature changes to 62 °C, find: a) the resulting normal stress in...
Required information The allowable shearing stress is 15 ksi in the steel rod AB and 8 ksi in the brass rod BC. A torque of magnitude T = 13 kip-in. is applied at A. T Steel Brass Determine the required diameter of rod AB. (Round the final answer to three decimal places.) The required diameter of rod AB is D in. Determine the required diameter of rod BC. (Round the final answer to three decimal places.) The required diameter of...
4.11. A shaft ABC is made of two segments AB and BC (Figure 4. 11). Segment 4B is solid with a diameter of 100 mm and BC is hollowed with an outer diameter of 75 mm and wall thickness of 5 mm. The shear modulus is 80 GPa for segment AB and 60 GPa for BC Extemal torques To=25 Nm in the counter-clockwise direction is applied at Cand 1s=10 Nm in the clockwise direction is applied at B. A counter-clockwise...
Figure Q1 The jib crane is pinned at A and supports a chain hoist that can travel along the bottom flange of the a) the force in rod BC b) the minimum diameter of rod BC (to the nearest 5 mm). c) the minimum diameter of pin B (to the nearest 5 mm). The material properties are listed in Table Q2 and use factor of safety of FS-2 (10 marks) beam boist Figure Q2 Table Q2: Material properties (MPa) Shear...
Required information The aluminum rod BCG= 26 GPa) is bonded to the brass rod AB (G=39 GPa). Each rod is solid and has a diameter of 12 mm. Take T = 130 Nm. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 200 mm Brass B 300 mm Aluminum С T Determine the angle of twist at C.
> I see no picture attached, thx
Daniel Cavallaro Mon, Oct 18, 2021 5:01 PM