What is the minimum depth setting for a 12.2m Concrete pole?

Question

Question

Answer 1

Answer #1

The depth setting for a Concrete pole lies between 1/3 to 1/2 of its height.

The minimum is 1/3 (one third of the height)

Thus,

12.2/3 = 4.067 m

The minimum depth setting for a 12.2m Concrete pole is 4.07 m (meters)

Upvote, if the answer was helpful. Have a nice and safe day.

Answer 2

Similar Homework Help Questions

What is the minimum depth setting for a 12.2m Concrete pole?

What is the minimum depth setting for a 12.2m Concrete pole?
What is the minimum setting depth of a limestone anchor in thinly bedded limestone?

What is the minimum setting depth of a limestone anchor in thinly bedded limestone?
What is the minimum length of pole for a 600v power line when installed in normal...

What is the minimum length of pole for a 600v power line when installed in normal soil?

10.3 What are the minimum and maximum percentages of steel allowed in an reinforced concrete column?...

10.3 What are the minimum and maximum percentages of steel allowed in an reinforced concrete column? Explain why it is necessary to specify these percentages.
A reinforced concrete beam has the following properties: Beam width, b = 320 mm Effective depth,...

A reinforced concrete beam has the following properties: Beam width, b = 320 mm Effective depth, d = 640 mm Concrete strength, f’c = 21 MPa Reinforcing steel strength, fy = 400 MPa If the factored shear force at the critical section is 210,000 N, compute the nominal shear carried by the shear reinforcement. EXERCISE - USD SHEAR 1. A reinforced concrete beam has the following properties: Beam width, b = 320 mm Effective depth, d = 640 mm Concrete...
Example CVEG 4303: Reinforced Concrete I One-Way Slabs A 5" thick concrete slab is reinforced for...

Example CVEG 4303: Reinforced Concrete I One-Way Slabs A 5" thick concrete slab is reinforced for tension with #4 bars spaced at 7". The effective depth is 4" Grade 60 bars and 8,ooo psi concrete will be used. 1.) Determine the design bending strength (фМп) of the slab. 2.) Check that ACI requirements for rebar strain, rebar spacing, and minimum reinforcement are met (ACI 7.3.3.1, ACI 24.3.2, and ACI 7.6.1.1 respectively). Note: Do not need to check temperature and shrinkage...

The bias R2 is replaced by a 15k ohm potentiometer. What minimum resistance setting causes saturation?...

The bias R2 is replaced by a 15k ohm potentiometer. What minimum resistance setting causes saturation? +15 V Rc 1.5 kΩ 22 kΩ BDc 150 4.7 kΩ 680 Ω
A rectangular concrete beam measures 12 inches wide and has a depth of 26 inches. The...

A rectangular concrete beam measures 12 inches wide and has a depth of 26 inches. The centroid of the tension rebars is located 4 inches from the tension surface of the beam. Use fy = 60 ksi f’c = 3 ksi, compressive failure strain of concrete = 0.003. (A) Find the required tension rebars As to carry Mu = 5,700 kips-in. Show that the steel ratio does not meet the ACI requirements. (B) What can you do to meet ACI...
Dimeter of pipe(D)m = 2.2 Depth of water (y)m= 1.4 Q.1. A (D) m diameter concrete...

Dimeter of pipe(D)m = 2.2 Depth of water (y)m= 1.4 Q.1. A (D) m diameter concrete pipe carries a water at a depth of (y) m shown in Figure: 1. The bed slope "S" is 1:500. Determine the discharge through the pipe. Take Chez's constant C=50. (6 Marks) Yim) Dim)

1. You want to determine the lateral pressure of fresh concrete for a 15 ft tall...

1. You want to determine the lateral pressure of fresh concrete for a 15 ft tall column. The concrete has a density of 145 lb/ft with a slump of 4 in, and a temperature of 66 °F. The mixture it contains a cement blend with 30% fly ash and retarders. Internal vibration will occur in intervals less than 4 ft in depth. Determine the lateral pressure and draw the pressure diagram if the concrete is placed at 15 ft/h. Check...