Answer:
Q3.) (2) point The pump at C produces a discharge of water at B of 0.035...
Q2.) (2) point Water is drawn into the pump, such that the pressure at the inlet A is -35 kPa and the pressure at B is 120 kPa. If the discharge at B is 0.08 m3/s, determine the power output of the pump. Neglect friction losses. The pipe has a constant diameter of 100 mm. Take (h = 2+0.55) m. B h
Q4. A pump draws water from a large reservoir and delivers it to another reservoir whose water surface is 10 m higher than the pump centreline and that the pump is 1.5 meter above the suction reservoir. The total suction and deliver pipe used is 21.1 m in length, 9 cm in diameter and has a Darcy friction factor f0.0339. The pump operates at 750 rpm and its characteristic performances are given in table below: Q (m3 s H (m)15...
A centrifugal pump test yields the following data: Pump Head Flow (m)(L/min) 30 25 20 40 The pump curve can be approximated by a parabola. This pump draws water from a large reservoir. The discharge of the pump feeds 150 m of 1.5 cm inside diameter pipe and then 225 m of 3 cm inside diameter pipe.. The two pipes both have a roughness of 0.5 mm The 3 cm pipe discharges to atmosphere a distance 40 m below the...
lunzontal pipe and pump system in the following figure discharges 0.01583 m3/s. The gage pressure iust before the pressure is 400 The m/s2 losses between 20°C water at 57 m3/h 0 kPa and just after the pump the gage a. The pump inlet diameter is 9 cm and the outlet diameter is 3 em. Let g-9.81 pump is 12 o Pwater9 kg/m, Hwate0.001002 kgm-s) and Pat the two pressure points and the pump. But consider frictional losses at the 9-cm...
Mechanical Lab II. Please answer asap with clear work. Thank
you!
1. A centrifugal pump performance data are shown in the following table for water. Pump speed-2500 RPM Pa or P2 (bar) P. or Pi (bar) Volume of water(L Time (sec) Input-Power (W) -0.3 20 60 100 For this data set, calculate the following i. Pump discharge capacity Q (LUs and GPM) ii. Pump head H (m and ft) iii. Fluid power Pr (Watt) iv. Brake power Pb (Watt) v....
Homework #4 Problem 5.87 9 of 16 The pump is used with a 3-in.-diameter hose to draw water from the cavity. Include frictional head losses in the hose of 1.5 ft for every 20 ft of hose. The hose has a total length of 140 ft·Nw = 62.4 lb/ft3. 3fti B 18ft( Part A If the discharge is 1.3 ft3/s, determine the required power developed by the pump Express your answer using three significant figures. hp Submit Provide Feedback Next...
Water is drawn into the pump, such that the pressure at the
inlet A is -45 kPa and the pressure at B is 110 kPa . The pipe has
a constant diameter of 100 mm. The discharge at B is 0.08 m3/s.
Take h = 2 m.
Determine the power output of the pump. Neglect friction
losses.
Course Homepage - Fall 2019T X Mastering Engineering Mastering x C Get Homework Help With Chege x + -ox € → C session.masteringengineering.com/myct/itemView?assignmentProblem...
4. The discharge pressure gauge reading is 5 lb/in2 (psi) for the pumping system shown in the sketch below, with the outlet nozzle discharging a 2-inch diameter stream of water directly to the atmosphere. The gauge pressure at the pump suction inlet at the point of incipient cavitation is (-2,071.12) lb/ft, i.e., for vapor pressure of water at 68° F of 50.54 lb/ft2 absolute, and standard atmospheric pressure 30 in Hg. Friction losses in the suction piping from the reservoir...
If a pump with the characteristic curve shown in the accompanying graph (Figure 2) is used to pump water from the lower to the upper tank (water flows from Tank 2 to Tank 1 in this question) shown in Figure 1. Use information provided in Figure 1 and assume that diameter of pipe AB is 600 mm (DAB 600 ) and diameter of pipe BC is 300 mm DBc 300 mm) a. Find the operation point of this systenm b....
3. A centrifugal pump performance data are shown in the following table for water. Pump speed 2500 RPM Pe or P2 (bar) P or Pi (bar) Volume of water (L) Time (sec) Input-Power (W -0.3 20 60 100 For this data set, calculate the following: i. Pump discharge capacity Q (L/s and GPM) ii. Pump head H (m and f) iii. Fluid power Pr(Watt) iv. Brake power Pb (Watt) v. Pump overall efficiency η (%) vi. Flow rate coefficient Ca...