In a test of the centrifugal pump shown in the image below the following data are...

Question

Question

In a test of the centrifugal pump shown in the image below the following data are taken: 100 mmHg (VCM) and P500 mmHg (ongel.

Add a comment Improve this question Transcribed image text

Answer 1

Answer #1

1.495 tot 11682 65cm G Datum 1 Pi = 160mm Hg (vacuum) P2 = 500 mnieg Di= 12cm Da 5cm SiG= Ogl Q- 200 gal/men = 0.0132 m3/s. 1

Add a comment

Answer 2

Similar Homework Help Questions

In a test of the centrifugal pump shown in the image below, the following data are...

In a test of the centrifugal pump shown in the image below, the following data are taken - 100 mmHg vacuum and D-500 mmHg ingel The pipe diameters are 12 cm and D5 Theo 203 gamin of light oil (SG-091), (2) 65 cm IG (1) References eBook & Resources Section Break Difficulty Hard wa 10.00 points Estimate the head developed in meters. (Round the final answer to one decimal place. You must provide an answer before moving to the next...
In a test of the centrifugal pump shown in the image below the following data are...

In a test of the centrifugal pump shown in the image below the following data are taken: p=100 mmHg Vacuum) and p2-500mmig langal. The pipe diameters are D = 12 cm and D - 5 cm. The flow rate is 200 galimin of light oil (SG = 0.99 (2) 65cm C (D References Book & Resources Section Break Difficulty:Hard 1. volu 10.00 points Required information Estimate the head developed in motors. (Round the final answer to one decimal place. You...
A centrifugal pump test yields the following data: Pump Head Flow (m)(L/min) 30 25 20 40 The pump...

A centrifugal pump test yields the following data: Pump Head Flow (m)(L/min) 30 25 20 40 The pump curve can be approximated by a parabola. This pump draws water from a large reservoir. The discharge of the pump feeds 150 m of 1.5 cm inside diameter pipe and then 225 m of 3 cm inside diameter pipe.. The two pipes both have a roughness of 0.5 mm The 3 cm pipe discharges to atmosphere a distance 40 m below the...

A 1 inch Bell and Gossett pump at best efficiency, running at 1750 min and a...

A 1 inch Bell and Gossett pump at best efficiency, running at 1750 min and a brake horsepower of 324, delivers 1050 galimin against a head of 105 References eBook & Resources Section Break Difficulty: Medium 5. 10.00 points Required information At what speed should the 11 in Bell and Gossett centrtugal pump be run, at best efficiency, to deliver 880 şalmin? Round the final answer to the nearest whole number Hints References Book & Resources Check my work 6....
mately 100 n+0.00 Water must be pumped through a pipe network that has a requaired head of approx where Q has units of gpm An engineer is considering using a centrifugal pump operating at 1 ugal p...

mately 100 n+0.00 Water must be pumped through a pipe network that has a requaired head of approx where Q has units of gpm An engineer is considering using a centrifugal pump operating at 1 ugal pump operating at 11s0 rpm with three possible impeler diameters: 6·T, and ir A) If at least 160 gpm of flow is needed, which (if any) of the impellers will meet this n 8) Estimate the pump efficiency and motor power for the 6...
1. A centrifugal pump performance data are shown in the following table for water. Pump speed-250...

Mechanical Lab II. Please answer asap with clear work. Thank you! 1. A centrifugal pump performance data are shown in the following table for water. Pump speed-2500 RPM Pa or P2 (bar) P. or Pi (bar) Volume of water(L Time (sec) Input-Power (W) -0.3 20 60 100 For this data set, calculate the following i. Pump discharge capacity Q (LUs and GPM) ii. Pump head H (m and ft) iii. Fluid power Pr (Watt) iv. Brake power Pb (Watt) v....

3. A centrifugal pump performance data are shown in the following table for water. Pump speed...

3. A centrifugal pump performance data are shown in the following table for water. Pump speed 2500 RPM Pe or P2 (bar) P or Pi (bar) Volume of water (L) Time (sec) Input-Power (W -0.3 20 60 100 For this data set, calculate the following: i. Pump discharge capacity Q (L/s and GPM) ii. Pump head H (m and f) iii. Fluid power Pr(Watt) iv. Brake power Pb (Watt) v. Pump overall efficiency η (%) vi. Flow rate coefficient Ca...
A centrifugal pump is placed above a reservoir as shown below. If the NPSHR is 17...

A centrifugal pump is placed above a reservoir as shown below. If the NPSHR is 17 ft and the flow rate is 32 ft3/s, determine the maximum height, 21, that the pump can be located above the reservoir surface without cavitation. Assume that the total head loss between the tank and pump inlet is 10 ft. The diameter of the pipe on the suction side of the pump is 12 inches. The reservoir surface is at atmospheric pressure, Patm =...
The system below uses a centrifugal pump to circulate water at 19°C, having a vapor pressure...

The system below uses a centrifugal pump to circulate water at 19°C, having a vapor pressure of 2320 Pa, from a low reservoir to a higher one through a cast iron pipe with a diameter of 35 cm and surface roughness of 0.25 mm. The minor head losses upstream of the pump are represented by EK1 = 0,6 and downstream by & K2 = 7. After several months of usage, it is noticed that the installation is noisy and consumes...

Question of Save & Exit Submit It is proposed to run a pump at 880 rpm...

Question of Save & Exit Submit It is proposed to run a pump at 880 rpm to pump water at 20°C through the system of the image shown below. The pipe is 20-cm clometer commerciel steel. For water, take p- 998 kg/m and p= 0.0010 kgs. For commercial steel, take=0.046 mm. gamin 2000 4000 3000 10000 192 hoo GB Hit Р. hp 139 12 134 100 B 10 43 m Pume 12 m References ellook & Resources Section Break Oculty...

In a test of the centrifugal pump shown in the image below the following data are...

Homework Answers