Page 1
Page 2
Page 3
Pls do comment in case of any doubt...pls do like...
vA = 4.6 ft/s vB = 9.2 ft/s Solve for vD using relative motion scalar method....
+ Relative-Motion Analysis of Two Particles Using Translating Axes < 5 of 5 n Review Learning Goal: Part A To analyze the motion of a particle using a translating frame of reference. Two particles, A and B, are moving along arbitrary paths and are at positions r A and rb from a common origin. The relative position of point B with respect to A is designated by a relative-position vector ТВА and is specified with the equation A cruise ship...
0.3M 201 B Given: VA = 2m/s down incline Find: VB, WAB Solve this using 2 different methods 2) I.C. 3) graphical
Part A Due to slipping, points A and B on the rim of the disk have the velocities v A = 4.6 ft/s and vB = 9.2 ft/s. (Figure 1) Determine the velocity of the center point C at this instant. Express your answer to three significant figures and include the appropriate units. μΑ ? VC = Value Units You have already submitted this answer. Enter a new answer. No credit lost. Try again. Figure 1 of 1 Submit Previous...
Dynamics. Please find the following. 1-using the relative velocity method 2-using the instantaneous center of rotation method thank-you in advance!. 6) In the position shown, calculate: (c) CD (a) vc (b) wBc WBC 305 mm min 254 mm 2 rad/s 45° 30°
Please help me answer the question using the circuit. Any method is acceptable. Thank You. **HERE IS A SAMPLE TABLE f w |Vi| |VA| |VC| |VD| |VA|/|Vi| |VC|/|VA| |VD|/|VC| φA φC φC-φA φD φD-φC 10 100 1000 10000 R2 w P+15V R1 A R2 B 2 с C2 HE D 3 Vi C1 R3 Vo -15V 3. Let R1 = 2.7 k12, R2 = 51k, R3 = 15 k12, C1 = .1 uF, and C2 = .1 uF. Assume that...
Note: help me solve problem 1.33 only using Fig P1.33 Answer: Shear stress A : 3670psi Shear stress B : 4320psi Thank you 22 CHAPTER 1 Stress 45° 10 m 200 lb 6 ft l 12 in. 2 ft o A 4 ft 3 ft 36 in. FIG. P1.33 FIG. P1.34 FIG. P1.35 1.33 The bracket is supported by 1/2-in. diameter pins at A and B (the pin at B fits in the 45° slot in the bracket)....
MEC311 Term Test, 2019w 2. 145%) This problem is about using work-energy and impulse-momentum principles. You must answer according to the notations and coordinate systems set up for you Answers based on other coordinate sysfem or notations will not be marked. Consider a sticky ball of weight Ws 0.1 [lb] located on an incline of angle 0-30-deg. The ball is initially placed on top of a compressed linear spring of spring constant k 10 [lb/ft]; see figure. It is released...
Learning Goal: To use the node-voltage method to solve circuits with branches containing only a voltage source. The node-voltage method is a general technique for solving circuits. Fundamentally, it involves writing KCL equations at essential nodes. When the circuit contains a dependent source, you must write a constraint equation for each dependent source, in addition to the KCL equations. When the circuit contains one or more voltage sources that are the only components in branches connecting two essential nodes, the...
Directions: Solve problems using the Dimensional Analysis method and show you work. 1. MD Ordered: Celftin Oral suspension 375 mg PO bid. Pharmacy sends: Ceftin Oral Suspension 125 mg/ 5 mL how many tsp will the nurse give ? oses 169 ol Medication CHAPTER NINE Calculating Oral Med APPLY LEARNED KNOWLEDGE9-4 Use the physician's orders and the MAR to onswer the following questions Electronic Medical Record Provider Orders Name S. Paent Age 35 GenderFDOB 09-10-xx MR # 36810Allergies NKDA Provider...
please help prepare a statement of cash flows using the indirect method. thank you! Merge & Center Paste 1 BIU Number Clpboard Font Alignment F144 A D 40 E Issued Common Stock for Cash 41 F Purchased Treasury Stock with Cash 42 43 Requirements 44 Prepare, in good form, a Statement of Cash Flows using the indirect method 45 46 Formatting 47 Do NOT use cents (00) in any records Journal entries, adjusting and closing entries do not contain dollar...