A calibration curve plotting E vs. pCd is used to measure the concentration of Cd2 in solution at 25 °C using a solid Cd electrode. What is the slope of the calibration curve in mV?
Thanks!
A calibration curve plotting E vs. pCd is used to measure the concentration of Cd2 in...
please answer all questions
The calibration curve and the calibration equation above was obtained by plotting absorbance Vs. [KMnO_4]. In the calibration equation y = 4.84E+03 x - 2.26E-01, what does y and x represent, respectively? If the absorbance of a KMnO_4 solution of unknown concentration is 0.833, calculate the concentration of KMnO_4 in the solution. Show your calculation.
A student created a Beer’s Law calibration curve by plotting absorbance vs. [CV]. The line of best fit is y = 42871x + 0.0500. If the absorbance of an unknown was found to be 0.69, what is its concentration? Hint: Answer includes 3 significant figures. Calculate the absorbance if the % transmittance is 82.4%.
Calibration data for a bromide ion‑selective electrode (ISE) was collected and recorded in the table. The potential of the ISE was measured against a saturated calomel electrode (SCE). All solutions were buffered at a pH of 7.56. A linear calibration curve can be constructed from this data as a plot of potential (in mV) vs. pBr. Determine the slope and y‑intercept of such a plot of the calibration data given. Br-M Potential (mV 0.300 -21.6 0.0300 36.7 0.00300 96.5 0.000300...
Potential (mV) [Br](M) 0.300 Calibration data for a bromide ion-selective electrode (ISE) was collected and recorded in the table. The potential of the ISE was measured against a saturated calomel electrode (SCE). All solutions were buffered at a pH of 7.56. A linear calibration curve can be constructed from this data as a plot of potential (in mV) vs. pBr. Determine the slope and y-intercept of such a plot of the calibration data given. -21.2 0.0300 36.2 95.7 0.00300 0.000300...
You begin preparation of the calibration curve to measure absorbance vs concentration of FeSCN2+. To do so, you add 4.614 mL of 0.200 M Fe(NO3)3 to a cuvette and then directly add 108 µL of 0.001 M KSCN. What is the resulting concentration of FeSCN2+, assuming complete conversion of SCN- to FeSCN2+? Enter your answer in units of mM to four digits after the decimal.
You are generating a calibration curve for absorbance vs. concentration for a colored solute. Using only the values provided, what would be the value of the slope of the line through these points? Provide your response to the nearest whole integer. concentration absorbance 0.002 M 0.245 0.003 M 0.783
You are generating a calibration curve for absorbance vs. concentration for a colored solute. Using only the values provided, what would be the value of the slope of the line through these points? Provide your response to the nearest whole integer. concentration absorbance 0.001 M 0.143 0.002 M 0.769
Calibration data for a bromide ion-selective electrode (ISE) was collected and recorded below. The potential of the ISE was measured against a saturated calomel electrode (SCE). All solutions were buffered at a pH of 7.56. A linear calibration curve can be constructed from this data as a plot of potential (in mV) vs. pBr. Determine the slope and y-intercept of such a plot of the calibration data given [Br] (M) Potential (mV) 0.300 0.0300 0.00300 96.4 0.000300 155.1 0.0000300 224.8...
Question 4 of 4 > Potential (my -21.9 Calibration data for a bromide ion-selective electrode (ISE) was collected and recorded in the table. The potential of the ISE was measured against a saturated calomel electrode (SCE). All solutions were buffered at a pH of 7.56. A linear calibration curve can be constructed from this data as a plot of potential (in mV) vs. pBr. Determine the slope and y-intercept of such a plot of the calibration data given. [Br"](M) 0.300...
In Part 1 of Experiment 1, you will be plotting a calibration curve (A vs [Ph2-]) to check your data during the lab period and use in your calculations after lab. Based on the sample data below, what is the εl value obtained for this experiment? A [Ph2-], M 0.104 3.04E-06 0.202 6.08E-06 0.291 8.69E-06 0.403 1.22E-05 0.52 1.52E-05