A sinusoidal voltage source of v(t) = 240√2sin( 2π50t + 30°) is applied to a non...
A sinusoidal voltage source of v(t) = 240√2sin( 2π50t + 30°) is applied to a non linear load, resulting in a non-sinusoidal current, which is expressed in Fourier series form as:
i(t)=10√2sin(2π50t)+2√2sin(10π50t)+1√2sin(18π50t)
Determine,
a) the active power, reactive power and power factor.
b) the distortion factor and distortion power.
c) the total harmonic distortion of the load current.
d) explain the power quality disturbance arise in this problem.
Homework Answers
Add Answer to:
A sinusoidal voltage source of v(t) = 240√2sin(
2π50t + 30°) is applied to a non...
R-L-C circuit Please write down clearly? In the circuit, the AC voltage is applied to the...
R-L-C circuit
Please write down clearly?
In the circuit, the AC voltage is applied to the R-L-C circuit. 10mH 100/2sin 10'r 0.2mF HH a) Find the current flowing through the circuit. Express in the instantaneous form i(t). Assume the steady state condition. (hint: use the complex impedance to calculate the current) b) Find the active power and the reactive power supplied by the voltage source.
A sinusoidal ac voltage source with a peak voltage of 28.3 V is connected across a...
A sinusoidal ac voltage source with a peak voltage of 28.3 V is connected across a pure resistive load. Choose the best answer for the dc voltage resulting in the same average power dissipated in the load? A) 28.3V B) 56.6 V C) 20 V D) 10 V
Problem 04: A voltage source is expressed by the following Fourier series: v(t) = -2 +...
Problem 04: A voltage source is expressed by the following Fourier series: v(t) = -2 + 5* sin(t) – 5*cos(t) – 3* sin(2*t) + 4*cos(2*t) – sin(3*t) – 6*cos(3*t) + 4*sin(4*t) + 6*cos(4*t). Now, (a) Express v(t) in amplitude-phase form. (b) Draw the amplitude and phase spectra of v(t) (c) Determine the effective value (rms value) of the voltage v(t) (d) If the voltage is applied across an impedance block as shown in the circuit below, determine the average power...
12. A sinusoidal voltage Δv = (75.0 V)sin(120t) is applied to a series RLC circuit with...
12. A sinusoidal voltage Δv = (75.0 V)sin(120t) is applied to a series RLC circuit with L = 20.0 mH, C = 130.0 μF, and R = 32.0 Ω. (a) What is the impedance of the circuit? Ω (b) What is the maximum current in the circuit? A 11.An AC power source has an rms voltage of 120 V and operates at a frequency of 60.0 Hz. If a purely inductive circuit is made from the power source and a...
A large transformer operating at no-load draws an exciting current of 5 A when the primary is connected to a 240 V, 50 Hz source (HELP)
Question 1: A large transformer operating at no-load draws an exciting current of 5 Awhen the primary is connected to a 240 V, 50 Hz source. From wattmeter testit is known that the iron losses are equal to 300 W. At short circuit the voltage applied is 24 Volts , the short-circuit current is 35 Amperes, the power meter reads 400 W. Calculate:i) The reactive power absorbed by the core;ii) The value of Rc and Xm of the magnetising branch; iii)...
Question 1 Assume the transformer to be ideal. Winding 1 is applied a sinusoidal voltage in...
Question 1 Assume the transformer to be ideal. Winding 1 is applied a sinusoidal voltage in steady state with 120 20° V at a frequency f 50 Hz. N1/N2=4. The load on winding 2 is a series combination of R and L with Z 4+j5 . Calculate the current drawn from the voltage source.
Consider the following circuit with an AC voltage source Vin = 1500V260° V connected to a...
Consider the following circuit with an AC voltage source Vin = 1500V260° V connected to a load. The total current drawn from the source 2. 15V2 275 A. Load Calculate . Load Impedance . Average Power(P) . Reactive Power (Q) . Power Factor . Complex Power (S) Apparent Power (ISI
A sinusoidal voltage Delta v = (75.0 V)sin(160 t) is applied to a series RLC circuit...
A sinusoidal voltage Delta v = (75.0 V)sin(160 t) is applied to a series RLC circuit with L = 40.0 mH, C = 130.0 mu F, and R = 42.0 Ohm. What is the impedance of the circuit? What is the maximum current in the circuit?
Figure 2.6 depicts this circuit as a voltage source applied to a resistor and inductor in...
Figure 2.6 depicts this circuit as a voltage source applied to a
resistor and inductor in parallel (disregard the capacitor for part
A), which is to be an equivalent to the load. Why is a
resistor and inductor in parallel used for the load versus just
using a resistor?
Find the following (show calculations):
Real power absorbed by the load.
Apparent power of the load.
Reactive power of the load. Don’t use the tangent
function. Instead, find the reactive power using the
apparent...
R-L-C circuit
Please write down clearly?
In the circuit, the AC voltage is applied to the R-L-C circuit. 10mH 100/2sin 10'r 0.2mF HH a) Find the current flowing through the circuit. Express in the instantaneous form i(t). Assume the steady state condition. (hint: use the complex impedance to calculate the current) b) Find the active power and the reactive power supplied by the voltage source.
Problem 04: A voltage source is expressed by the following Fourier series: v(t) = -2 + 5* sin(t) – 5*cos(t) – 3* sin(2*t) + 4*cos(2*t) – sin(3*t) – 6*cos(3*t) + 4*sin(4*t) + 6*cos(4*t). Now, (a) Express v(t) in amplitude-phase form. (b) Draw the amplitude and phase spectra of v(t) (c) Determine the effective value (rms value) of the voltage v(t) (d) If the voltage is applied across an impedance block as shown in the circuit below, determine the average power...
Question 1 Assume the transformer to be ideal. Winding 1 is applied a sinusoidal voltage in steady state with 120 20° V at a frequency f 50 Hz. N1/N2=4. The load on winding 2 is a series combination of R and L with Z 4+j5 . Calculate the current drawn from the voltage source.
Consider the following circuit with an AC voltage source Vin = 1500V260° V connected to a load. The total current drawn from the source 2. 15V2 275 A. Load Calculate . Load Impedance . Average Power(P) . Reactive Power (Q) . Power Factor . Complex Power (S) Apparent Power (ISI
A sinusoidal voltage Delta v = (75.0 V)sin(160 t) is applied to a series RLC circuit with L = 40.0 mH, C = 130.0 mu F, and R = 42.0 Ohm. What is the impedance of the circuit? What is the maximum current in the circuit?
Figure 2.6 depicts this circuit as a voltage source applied to a
resistor and inductor in parallel (disregard the capacitor for part
A), which is to be an equivalent to the load. Why is a
resistor and inductor in parallel used for the load versus just
using a resistor?
Find the following (show calculations):
Real power absorbed by the load.
Apparent power of the load.
Reactive power of the load. Don’t use the tangent
function. Instead, find the reactive power using the
apparent...
Most questions answered within 3 hours.
-
Explain why you should not lose any LDH activity when you
centrifuge a crude sample at...
asked 44 seconds ago -
An AA battery (object), standing on end, is placed to the left
of a diverging lens...
asked 1 minute ago -
After you measure the self-inductance of a coil, you unwind it
and then rewind one third...
asked 2 minutes ago -
1. Which of the following best describes a transistor?
A) a small electrical circuit made from...
asked 3 minutes ago -
Use generating function to find the number of distributions of
20 people into four different rooms...
asked 18 minutes ago -
The following data set consists the number of minutes a sample
of 25 people run every...
asked 22 minutes ago -
Suppose vacuum cleaners are part of the market basket used to
compute the CPI. Suppose also...
asked 34 minutes ago -
What intermediate results after the addition of H3O+ to
E-3-methyl-2-pentane?
pentene*
asked 39 minutes ago -
Potassium hydrogen phthalate is a solid, monoprotic acid
frequently used in the laboratory to standardize strong...
asked 58 minutes ago -
1-Describe the 3 major classes of ownerships of retailers
2-What are the differences between consumer and...
asked 41 minutes ago -
A Student takes a sample from a table top in the student lounge
using a sterile...
asked 49 minutes ago -
Give an answer that's easy to understand. Define stack data
structure. Show how the Stack operations...
asked 58 minutes ago