A water tank filled with solar-heated water at 40°C is to be used for showers in...
Please solve a,b,c,d,e,f 1) A water fountain is to be installed at a remote location by attaching a cast iron pipe directly to a water main through which water is flowing. The entrance to the pipe is sharp-edged 15m (K-0.5), and the 15m long piping system involves three 90 bends without vanes (K1.1), a fully open gate valve (K.-0.2), and a fully open angle valve (K-5). If the diameter of the pipe is 2 em and the system is to...
fluid mechanics ASAP please Problem 4 (50 points) Water is discharged from a reservoir at a rate of 18.103 m3/s using two horizontal cast iron pipes connected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged. Losses...
Problem 4 (50 points) water is discharged from a reservoir at a rate of 18.103 m2/s using two horizontal cast iron pipes nected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged. Losses associated with the connection...
The total length of the piping system made of cast iron providing hot water to a house is considered to have a 42m length with a constant diameter. The entrance gage pressure is 85 kPa and exit at 15 kPa gaged. Consider the water density equal 980 Kg/m' and the viscosity 1.138x10 Kg/ms. a) Compute the piping system diameter if the volumetric flow rate provided by this system is equal to 0.1 L/s. There is no pump present in this...
Fig. Q4 shows a piping arrangement used in a food processing facility to transfer water, at 40 C, from a tank, through a heat exchanger to an elevated tank. A suitable pump is selected which, when installed, delivers the water at 2.5 m'/hr. The pipe diameter is 40 mm and the Absolute Roughness of the pipe material is 0.00008 m. The Loss Coefficients [K Factors] for the Bend and Heat Exchanger are shown in Fig. Q4 4. 2 m K...
Problem 3: Flow Rate Water (20 degrees C) drains from a pressurized tank through a pipe system as shown in the figure. The head of the turbine is equal to 116 m. If entrance effects are negligible, determine the flow rate. (assume f-0.038 to start iterations) 50 kPa (I e 200 m, D 0.1 m 0.0008 m Valve (KL 5.0) 200 m Turbine Free Jet 90° elbows (KL 1.0)
Water at 15 C is drained from a large reservoir using two horizontal plastic pipes connected in series. The first pipe is 13 m long and has a 10-cm diameter, while the second pipe is 35 m long and has a 5-cm diameter. The water level in the reservoir is 18 m above the centerline of the pipe. The pipe entrance is sharp-edged, and the contraction between the two pipes is sudden. Neglecting the effect of the kinetic energy correction...
(100 points) Water at 25°C is pumped at a rate of 0.075m's from a reservoir 20m above a pump to a free 1. discharge (this means discharged to atmosphere) 35m above the pump. The pressure on the intake side of the pump is 150kPa and the pressure on the discharge side of the pump is 450kPa. The pipe between the reservoir and the pump is 3 meters of Sin diameter cast iron. From the pump to the discharge the pipe...
Question (20 marks Analysis only required Water at 15°C is discharged freely to atmosphere from a reservoir at 18 L/s through two horizontal pipes in series and a pump-motor assembly in between as shown in figure below. First pipe-A is made of cast Iron and is 20m in length with a 60mm dia. The second pipe-B is 35 m in length, has a 40 mm diameter with friction factor 0.0331. The pipe entrance from reservoir is sharp edged. Neglect any...
Fluid Mechanics & Fluid Power Determine the NPSH available. The pressure in the tank is - 20 kPa at 70 °C (atmospheric pressure is 100.5 kPa). The water level in the tank is 2.5 above the pump inlet. The pipe is 1%", schedule 40 with a total length of 12 m. The elbow is standard, and the globe valve is fully open. The flow rate is 95 L/min. FIGURE 13.27 llustration of pump performance for different impeller diameters with net...