Homework Answers
Add Answer to:
Answer must match one of the given options
cular shaft has an outside diameter of 12...
need solution step by step to question “H” (H) For the shaft of question (G) above, what are the X and Y forces on each of bearings B and E? Upward Y force on bearing E: Rey263 b Upward Y force...
need solution step by step to question “H”
(H) For the shaft of question (G) above, what are the X and Y forces on each of bearings B and E? Upward Y force on bearing E: Rey263 b Upward Y force on bearing B: Rey1,838 b Outward X force on bearing E: Rex Outward X force on bearing B: Re1,569 b Answer Box 804 lb 36 REy Sum of Y moments around E = 0 Sum of Y Forces on...
Problem 1 (35pts) A solid 45.0mm diameter shaft is made out of cold rolled steel with...
Problem 1 (35pts) A solid 45.0mm diameter shaft is made out of cold rolled steel with σ,w-1000MPa in both tension and It is simultaneously exposed to force P- 180kN T-9.SKN m and a bending moment M- 1.25kNm. The directions of loads are shown on the figure. On the basis of z M 1) the maximum-shear stress (MMS) theory 2) the maximum distortion energy (MDE) theory is the shaft overstresses in point A at the central top location? Equations section properties:As-d2...
Saved Question 20 1 points The following is the torque versus angle of twist diagram for...
Saved Question 20 1 points The following is the torque versus angle of twist diagram for a 0.75 inch diameter steel bar tested in torsion. The gage length of the bar is 3 inches. The angle of rotation and torque at points and Pare (0.8 radian, 1500 in-lb) and (11.3 radian, 4000 in-Ib) respectively. The power-law curve fitting relation for the data above the yield point is given by T-32980021, where T is in in-lb and is in radian Torque...
1. The following is a one-layer truss structure fabricated from aluminum tubing with outside diameter and...
1. The following is a one-layer truss structure fabricated from aluminum tubing with outside diameter and wall thickness as 0.4 inch and 0.05 inch, respectively. The Young's modulus and Poisson's ratio for aluminum are E= 10 x 10°psi, v=0.33, respectively. The applied load P is 60 Ib. Please answer = 60° B Ra all Cled URb The internal force for member AC is: -30 lb 34.6 lb 30 lb -34.6 lb Question 2 1 points Save Answer 1. The following...
PLEASE CAN YOU SOLVE THE HOMEWORK ACCORDING TO THE ITEMS AND BY STATING WHICH ITEM THE...
PLEASE CAN YOU SOLVE THE HOMEWORK ACCORDING TO THE ITEMS AND BY
STATING WHICH ITEM THE ANSWERS BELONG TO?
THE ANSWER IS EXPECTED AS SOON AS POSSIBLE
EMEGENCY HOMEWORK
The shaft EFG, which is running at constant speed of n (rev/min) and transmitting a power of P (kW), contains gear F. Gear F transmits torque to shaft ABCD through gear C, which drives the chain sprocket at B, transmitting a force P as shown. Sprocket B, gear C, and gear...
1: Given the power transmission system shown below Input: 30 hp, 2,000 rpm 12 pitch 18...
1: Given the power transmission system shown below Input: 30 hp, 2,000 rpm 12 pitch 18 teeth N C Rotation Hydraulic Pump 5 hp Water Pump, 6 hp 20° pressure angle 8 pitch 20 teeth 20° pressure angle 27 teeth 40 teeth Input Pump Output Bearing (typical) p (NP) Find: A Determine the rotation direction, rotational speed, and pitch diameter of each gear Pitch Diameter (in) Rotational Speed (rpm) Gear 1333 rmp B. Determine the hp and torque in shaft...
need solution step by step to question “H”
(H) For the shaft of question (G) above, what are the X and Y forces on each of bearings B and E? Upward Y force on bearing E: Rey263 b Upward Y force on bearing B: Rey1,838 b Outward X force on bearing E: Rex Outward X force on bearing B: Re1,569 b Answer Box 804 lb 36 REy Sum of Y moments around E = 0 Sum of Y Forces on...
Problem 1 (35pts) A solid 45.0mm diameter shaft is made out of cold rolled steel with σ,w-1000MPa in both tension and It is simultaneously exposed to force P- 180kN T-9.SKN m and a bending moment M- 1.25kNm. The directions of loads are shown on the figure. On the basis of z M 1) the maximum-shear stress (MMS) theory 2) the maximum distortion energy (MDE) theory is the shaft overstresses in point A at the central top location? Equations section properties:As-d2...
Saved Question 20 1 points The following is the torque versus angle of twist diagram for a 0.75 inch diameter steel bar tested in torsion. The gage length of the bar is 3 inches. The angle of rotation and torque at points and Pare (0.8 radian, 1500 in-lb) and (11.3 radian, 4000 in-Ib) respectively. The power-law curve fitting relation for the data above the yield point is given by T-32980021, where T is in in-lb and is in radian Torque...
1. The following is a one-layer truss structure fabricated from aluminum tubing with outside diameter and wall thickness as 0.4 inch and 0.05 inch, respectively. The Young's modulus and Poisson's ratio for aluminum are E= 10 x 10°psi, v=0.33, respectively. The applied load P is 60 Ib. Please answer = 60° B Ra all Cled URb The internal force for member AC is: -30 lb 34.6 lb 30 lb -34.6 lb Question 2 1 points Save Answer 1. The following...
PLEASE CAN YOU SOLVE THE HOMEWORK ACCORDING TO THE ITEMS AND BY
STATING WHICH ITEM THE ANSWERS BELONG TO?
THE ANSWER IS EXPECTED AS SOON AS POSSIBLE
EMEGENCY HOMEWORK
The shaft EFG, which is running at constant speed of n (rev/min) and transmitting a power of P (kW), contains gear F. Gear F transmits torque to shaft ABCD through gear C, which drives the chain sprocket at B, transmitting a force P as shown. Sprocket B, gear C, and gear...
1: Given the power transmission system shown below Input: 30 hp, 2,000 rpm 12 pitch 18 teeth N C Rotation Hydraulic Pump 5 hp Water Pump, 6 hp 20° pressure angle 8 pitch 20 teeth 20° pressure angle 27 teeth 40 teeth Input Pump Output Bearing (typical) p (NP) Find: A Determine the rotation direction, rotational speed, and pitch diameter of each gear Pitch Diameter (in) Rotational Speed (rpm) Gear 1333 rmp B. Determine the hp and torque in shaft...
Most questions answered within 3 hours.
-
1 – Balance the following
Bi(OH)3 + SnO22- →
SnO32- +
Bi
asked 8 minutes ago -
Explain what we mean by "The electric field at the point marked
X is 10 N/C."...
asked 19 minutes ago -
What is the positive energy states in Dirac’s picture? It says
that it leaves an empty...
asked 17 minutes ago -
A mutual fund manager has a $20 million portfolio with a beta of
1.7. The risk-free...
asked 17 minutes ago -
Given the following contribution margin income statement
Sales (15000 units 35
$/units)
asked 17 minutes ago -
The heights in feet of some of the girls of SEU
are: 5.8, 6.1, 5.9, 5.4, 5.6,...
asked 49 minutes ago -
Caspian Sea Drinks is considering the purchase of a new water
filtration system produced by Rube...
asked 54 minutes ago -
Compare and contrast the
social media of Pepsi and Coke? which one is most effective and...
asked 54 minutes ago -
1.
Who initiates a lockout?
Group of answer choices
management
employees
unions
arbitrators
asked 55 minutes ago -
Many celebrities and public figures have Twitter accounts with
large numbers of followers. However, some of...
asked 1 hour ago -
In #13-16, use the following information. At the 0.01 level of
significance, test the claim that...
asked 1 hour ago -
Suppose you wanted to make a buffer with pH 3.00. What chemicals
would you grab off...
asked 1 hour ago