please explain how you do it QUESTION 5 Q 5(a) Distinguish between normal stress and allowable...
P1.12 A simple pin-connected truss is loaded and supported as shown in Figure P1.12. The load P is 200 kN. All members of the truss are aluminum pipes that have an outside diameter of 115 mm and a wall thickness of 6 mm. Determine the normal stress in each truss member. Assume truss dimensions of a-12.0 m, b - 7.5 m, and c 6.0 m. FIGURE P1.12
solve incorrect answers please Your answer is partially correct. Try again. A simple pin-connected truss is loaded and supported as shown in the figure. All members of the truss are aluminum pipes that have an outside diameter of 4.75 in. and a wall thickness of 0.283 in. Determine the normal stress in each truss member. Assume P = 8 kips, Q = 7 kips, a = 7 ft, b = 10 ft, and h - 9 ft. The stresses are...
Diameter of pin 2 mm. All pins are in single shear. Question 1: A light plane structure is supported by a roller at A and a pin at D and is subjected to a load of Pat F as shown in the figure. All the members have rectangular cross section with height 5 mm and thickness 1 mm. Tensile/Compressive strength of the members = 80 MPa, Shear strength of the pin = 50 MPa. Consider an appropriate factor of safety....
1. The members of truss are attached together by pins having 5 cm in diameter and 10 cm in length. The truss is supported by a frictionless pin at one end (joint A) and a roller system at the other joint k). The load Lis equal to 5 kN. The section view of the truss member is below and it is homogeneous all along the truss. Elastic modulus is 200 GPa, shear modulus is 75 GPa for the truss. (a)...
Question I.5 Figure 1.5 shows a frame with loads at A and D. Select the closest value for the magnitude of the total reaction at B. Assume the weight of the frame is zero. 40 kN VE 96.2 kN (a) (Ь -40 kN 5 m (c) -87.5 kN 30 kN (d) 57 kN 4m ao 1 m (e) 50 kN Figure L.5 Low mass frame Question I.6 In the shear and bending moment equations for beams, which of the following...
Properties for all problems Sut = 80 ksi, 5= 60 ksi, Sf = 40 ksi, q=0.85 (notch sensitivity), steel E = 30e6 psi Remember we use Modified-Goodman for all calculations Problem 1 A 1-inch diameter rod that is 8 inches long has a bearing at one end and another bearing at 6 inches (treat bearings as simple supports). A vertical load is applied at the end of the overhanging rod and a torque is transmitted through the length of the...
Hi! Really stuck on this question. Could I please have some help? Question 1 (This question continues from Topic 2 Q1) Member ABCD is loaded and supported as shown in Figure 1. Select a suitable minimum weight square hollow section (SHS) for member CD from the table provided below, checking for buckling and/or squashing where appropriate. Assume both ends of CD are pinned and the yield stress is 350MPa and E-200,000 MPa 50 kN 30 kN 10 kN/m 30 kN...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...
pleas help me in this do any question you know using National Electrical Code 2011 Applied Electricity NEC worksheet t hree Copper conductors with THHN insulation run in Electrical A branch-circuit Consther conductors. The conductor terminations are rated for a maximum ure in the area of this installation is not expected to exceed 30C size 8 AWG, the maximum ampacity of the conductors If the conductors for this circuit are permitted A 40 amperes. B. 50 amperes. to be used...