Homework Answers
Add Answer to:
s: A wind turbine operates under the fol... A wind turbine operates under the following conditions...
What is the power coefficient for the Vestas V52-850 kW wind turbine at rated conditions? Rated...
What is the power coefficient for the Vestas V52-850 kW wind turbine at rated conditions? Rated capacity (kW) 850 Cut-in speed (m/s) 4 Cut-out speed (m/s) 25 Rated wind speed (m/s) 16 Rotor diameter 52 Swept area (m^2) 224 Rotor speed (rpm) 14-31.4
Question 30 6 points Save Answer (LO4) A wind turbine with a 40-m-diameter rotor is rotating...
Question 30 6 points Save Answer (LO4) A wind turbine with a 40-m-diameter rotor is rotating at 21 rpm under steady winds at an average velocity of 14.7 m/s. The electrical power output from the generator is 350 kW. The efficiency of the gearbox is 93% and generator efficiency is 86%. Take the density of air to be 1.013 kg/m. Answer the following questions; use the white paper to work-out your calculations and then choose the correct answer from the...
. A typical commercial wind turbine costs approximately $2 million per MW of installed power and...
. A typical commercial wind turbine costs approximately $2 million per MW of installed power and requires 5.76 TJ per million dollars of energy to manufacture the wind turbine. (a) Calculate the amount of energy that is consumed (i.e. energy invested) in the manufacture ofa 1.5 MW wind turbine, assuming that turbine manufacture requires 5.76 TJ per million dollars spent. (TJ Tera-joules 1012 joules) (b) If the wind turbine has blades that are 40 meters (radius) long and the average...
Consider a 1 MW, 50 m diameter horizontal axis, fixed wind turbine operating at a wind...
Consider a 1 MW, 50 m diameter horizontal axis, fixed wind turbine operating at a wind speed of 12 m/s. 3 blades mounted on a cast iron hub drive a generator through a gearbox of overall ratio 1:50. The induction generated is connected directly to the 60 Hz network and keeps the high speed shaft at 1500 RPM. Ignoring all other loses, calculate CP, lamda, rotor tip speed, and torque on low and high sides of the shaft.
8 blade turbine ,a wind speed of 36 km/h to pump water at the rate of...
8 blade turbine ,a wind speed of 36 km/h to pump water at the rate of 6m3/h, with a lift of 6m, efficiency pump 50% and efficiency rotor to the pump 80% , power coefficient 0.3 and the tip speed ratio is 1.0.Density of water 1000kg/m3, air 1.2kg/m3 and g = 9.81 m/s2. 1= the radius of the rotor (m) 2= the rotational speed of the rotor( rpm)
Consider the blade of the wind turbine (Fig. 2, next page), having the following properties: Blade...
Consider the blade of the wind turbine (Fig. 2, next page),
having the following properties:
Blade radius, R=19.0 m Rotor angular speed,
Ω=5.0 rad/s Blade total mass, Mb=900 kg Offset, eR (additional
information below)
Hinge spring stiffness, 7*106 (N-m/rad)
See Fig. 2 on the next page
Consider the blade of the wind turbine (Fig. 2, next page), having the following properties: Blade radius, R-19.0 m Rotor angular speed, Ω 5.0 rad/s Blade total mass, M, 900 kg Offset, eR (additional...
Question 30 6 points Save Answer (LO4) A wind turbine with a 40-m-diameter rotor is rotating at 21 rpm under steady winds at an average velocity of 14.7 m/s. The electrical power output from the generator is 350 kW. The efficiency of the gearbox is 93% and generator efficiency is 86%. Take the density of air to be 1.013 kg/m. Answer the following questions; use the white paper to work-out your calculations and then choose the correct answer from the...
. A typical commercial wind turbine costs approximately $2 million per MW of installed power and requires 5.76 TJ per million dollars of energy to manufacture the wind turbine. (a) Calculate the amount of energy that is consumed (i.e. energy invested) in the manufacture ofa 1.5 MW wind turbine, assuming that turbine manufacture requires 5.76 TJ per million dollars spent. (TJ Tera-joules 1012 joules) (b) If the wind turbine has blades that are 40 meters (radius) long and the average...
Consider the blade of the wind turbine (Fig. 2, next page),
having the following properties:
Blade radius, R=19.0 m Rotor angular speed,
Ω=5.0 rad/s Blade total mass, Mb=900 kg Offset, eR (additional
information below)
Hinge spring stiffness, 7*106 (N-m/rad)
See Fig. 2 on the next page
Consider the blade of the wind turbine (Fig. 2, next page), having the following properties: Blade radius, R-19.0 m Rotor angular speed, Ω 5.0 rad/s Blade total mass, M, 900 kg Offset, eR (additional...
Most questions answered within 3 hours.
-
From past history, the scores on a statistics test are normally
distributed with a mean of...
asked 11 minutes ago -
Calculate the gravitational field strength on the highest peak
of Everest (8848 m above the Earth).
asked 11 minutes ago -
the energy value of carbohydrates is 4.0 cal/g. calculate the
energy in 250 g of carbohydrates,...
asked 13 minutes ago -
i
need the summary of this article “Why I Don’t Trust The Video Games
Cause Violence”...
asked 32 minutes ago -
Draw the reactants and products of the following
reaction:
3-ethyl-2-heptene + HOH → 3-ethyl-3-heptanol +
3-ethyl-2-heptanol...
asked 30 minutes ago -
Determine the ratio of adipic acid and butylene glycol that
should be used to obtain a...
asked 39 minutes ago -
Calculate the ratio of the resistance of 11.0 m of aluminum wire
2.5 mm in diameter,...
asked 32 minutes ago -
Kinkaid Co. is incorporated at the beginning of this year and
engages in a number of...
asked 36 minutes ago -
when setting up a simple pendulum, calculate the string length
required for the period to equal...
asked 55 minutes ago -
: A small but very close dense mass of 389 kg is brought close
to a...
asked 55 minutes ago -
Create a class called Hotel. The hotel class will track the
current reservations for your one-room...
asked 1 hour ago -
In space, a 4.0 kg metal ball moving 30 m/s has a head on
collision with...
asked 1 hour ago