nprClapters 6, 9 and 10 1 H 12V Vout in -12V Qlh Given Vin 10 cos(20,0001)...

Question

Question

Answer 1

Answer #1

to K 12 ow X-wl3( 0000) (1): 20,000 peed loaE impedance(lo Ks)//0 Civen Circuit invetnfer. 000+ 4000 Vin V, Vout Voot = 3.gut

Answer 2

Similar Homework Help Questions

Given Vin= 10 cos(200t). What is the steady state output Vout

Given Vin= 10 cos(200t). What is the steady state output Vout State your answer in the rectangular form Real + j Imaginary.
Question 1 Not complete Marked out of 10.00 22nF Flag question 12V 10kQ J Vout in...

Question 1 Not complete Marked out of 10.00 22nF Flag question 12V 10kQ J Vout in -12V AC Qlb Given Vin 10 cos(200t). What is the steady state output V? State your answer in the rectangular form Real + j Imaginary out out
100mH 50Ω 0.1uF AC Vab Vin Q4f Given Vin 12 cos (10,000 t) Find the Thévenin...

100mH 50Ω 0.1uF AC Vab Vin Q4f Given Vin 12 cos (10,000 t) Find the Thévenin phasor equivalent of this circuit. Zn (rectangular form)-200 +j -1000 VTh (rectangular form) - 24 Ω(Ohm) Check

In in in out Q5e Given: Vin-25 cos (4,000t) Volts Rin 40 kΩ (kilo Ohm) Cin-0.1...

In in in out Q5e Given: Vin-25 cos (4,000t) Volts Rin 40 kΩ (kilo Ohm) Cin-0.1 μF (micro F) Rf-10 Ω (kilo Ohm) Rout-140 (kilo Ohm) R2-10 Ω (Ohm) The opamp has power input rails at +15V and -15V Find the steady-state output voltage Vout which is the voltage across the resistor R out (Degrees) Volts cos (4,000t+ out State the voltage magnitude as positive and state the phase angle as a positive angle (counterclockwise from the origin) in the...
3. The input signal to a certain filter is given by Vin(t) = 2cos (10 state...

3. The input signal to a certain filter is given by Vin(t) = 2cos (10 state output is given by Vout(t) = cos(10000 t + 20°). Determine the filter this will include both a magnitude and phase angle). * 2cos (10000nt - 25%) and the steady- °). Determine the transfer function of
(10) A Schmitt trigger is used to digitize a sinusoidal signal 6. Given that if Vin and 0.55Vo, then Vout-V if Vin0.5Vo...

(10) A Schmitt trigger is used to digitize a sinusoidal signal 6. Given that if Vin and 0.55Vo, then Vout-V if Vin0.5Vo, then Vout 0 Plot the behavior of the Schmitt sensor above for a cosine wave with maximum amplitude of Vo, (Vpeak-to-peak 2Vo) for two full cycles (2T where T is the arbitrary period) Assume zero offset and zero phase shift for the cosine wave. Identify key points on the graph. (10) A Schmitt trigger is used to digitize...

Problem 5: (20 points) Given the following circuit VIN L Vout R a) Write the loop...

Problem 5: (20 points) Given the following circuit VIN L Vout R a) Write the loop equation for the circuit, and then find the transfer function Vout(s) H(S) = Express H(s) so that the coefficient of the s in the denominator is 1. Vin(s) b) If Vin(t) is 20u(t), find out(t). c) If Vin(t) is 20u(t) find the final value using the final value theorem (show your work), d) Assume (R/L) = 10, if the input is Vin(t) = 100...
Find the circuit diagram of the transfer function: H(s)=Vout(s)/Vin(s) = (10^6)/(s^2+100s+10^6)

Find the circuit diagram of the transfer function: H(s)=Vout(s)/Vin(s) = (10^6)/(s^2+100s+10^6)
Mark with an X, the best answer for each statement below. Show your reasoning 9. EXTRA CREDIT: The ac circuit in Fig. 9(a), with the output VouT, acts as a: [2 points extra credit] a. 12 F Vin (t) 6...

Mark with an X, the best answer for each statement below. Show your reasoning 9. EXTRA CREDIT: The ac circuit in Fig. 9(a), with the output VouT, acts as a: [2 points extra credit] a. 12 F Vin (t) 6 S2 low-pass filter (see Table Vourl t) band-pass filter (see Table) band-stop filter (see Table) high-pass filter (see Table) 12 H iv. V. Fig. 9 (a) _ None of the above Table: Filter Definitions Pass Stop Low-Pass b. For the...

A MOSFET is wired as a common-source amplifier as shown below. The input voltage vIN is...

A MOSFET is wired as a common-source amplifier as shown below. The input voltage vIN is the total of the source for biasing the circuit at its operating point (vBIAS), and a small signal ac source providing the signal that we want to amplify (vin). The total output voltage is vO. a) Assume VDD = 5?, VIN = 2?, and ? = 4?Ω in the circuit and the MOSFET parameters are K = 0.5??/?2, VTH 1?, and ? = 0.05V-1....