Problem V-B In the circuit shown in Fig. V-B, suppose RE = RG= Ru= Ri =...
Question 2 (10%) The input to the circuit shown in Fig. 2 is the voltage source vs(t). The output is the voltage across two open terminals, vo(). If v()-3-(t) V, the output is the voltage vo()-10+Se30* V for 20. Determine the values of Ri and R2. 2 sa) olt) Fig. 2
this is all thats given Problem IV-B In the circuit of Fig. IV-B(a), determine: K, I, I, I in terms of V, and resistive elements and show that: V B I3 px{I,x(R, +2R2)-V,)/ (R, + 2R 2 ) ] (i) FIG. IV-B(a): Id-"A RI R3 I1 I+ R2 KI3 I3 Vo In the circuit of Fig. IV-B(b) shown below 11 Determine: K, 1, 1, Is and V = B I3 elements in terms of Vo and resistive (a) Show that...
P2: (40points) As shown below (Fig.1), A strain gage with gage factor of 2.02 is mounted on the bottom of a beam to measure the strain on the surface of the beam. The beam's Young's Modulus is 193 GPa. A wheatstone bridge circuit was constructed as sketched in Fig. 2. All resistors including the gage itself is 12002. Supply voltage is 5.0 V DC. The bridge is initially balanced when there is no load Strain gage Fig.1 Ri R2 DC...
As shown below (Fig.1), A strain gage with gage factor of 2.02 is mounted on the bottom of a beam to measure the strain on the surface of the beam. The beam's Young's Modulus is 193 GPa. A wheatstone bridge circuit was constructed as sketched in Fig. 2. Al resistors including the gage itself is 1202. Supply voltage is 5.0 V DC. The bridge is initially balanced when there is no load (a). when a downward load is added, will...
Q1. For the cascade amplifier circuit shown in Fig (1): a) What are the functions of the capacitors C, C2 and C3? And what are the functions of the capacitors Cs and CE? b) What are the functions of the resistors RD and Rc? c) Draw the DC biasing circuits for each stage. d) Find loa, VGsa, VDs and gm for the JFET stage (you may use either mathematical or graphical methods) e) Calculate l, Ic, le and Ve for...
vi Ri ii V3 R4 V5 Rs jis R7 In the circuit, Vg = 126 V, R2 = 9 Ohm, R3 = 7 Ohm, R4 = 4 Ohm, R5 = 29 Ohm, R6 = 10 Ohm and R7 = 7 Ohm. The current i2 = 3 A. (A) What is the resistance R1? (unit: Ohm) 23.04Ohm Submit Answer Incorrect. Tries 2/5 Previous Tries (B) What is the power supplied by the voltage source Vg into the circuit? (unit: W) Submit...
In the circuit of Fig. 8.98, (W/L)1–3 = 50/0.5, Ipi = |Ip2| = |Ip3| = 0.5 mA, and R$ı = RF = Rp2 = 3 kΩ 3. VDD VoHE M2 х Vin HE M1 Vout -W- RE Rs13 Rp2 Figure 8.98 (a) Determine the input bias voltage required to establish the above currents. (b) Calculate the closed-loop voltage gain and output resistance.
6. Find Vi in the following circuit if VR2 3 V, I -2 A, RI 100 , and R2 50 . Ry VR R.y 7. What is the output voltage (Vo) of the summing op-amp below? 1000 kn 200 k2 50 k2 +5 V 100 k2 -5 V V. out 8. For the operational amplifier circuit depicted below: a. Determine Vout in terms of the resistors: Ri, R2, R3, R4 and I R1 qut R- (current source) for the operational...
V = a) *R) V – (1) Vim (1) 3. The difference amp shown in Fig. 3(b) of the lab manual has an output voltage which depends upon the two input voltages according to the equation: R4 (R1+R1 R3+R4 R1 a. Show that when all of the resistors, R1, R3, R4, and Rf are set to 10 kA (as shown in Fig. 3(b)) the output voltage simplifies to Vo = Vp - Vm= e(t). b. Assume that Rf = 10...
Problem 1130 pts 1. [12 pts] For the circuit shown in Fig. 1, istance Rm when the switch is open. What type of voltage gain Vo/Vin and the input resistance Rin when the switch is close. What type of a) Find the voltage gain val vin and the input resistance Rin when the switch is open b) Find the amplifier is this? amplifier is this? tin vo R Fig. 1 [18 pts] Design a circuit that implements the following: Vo(t)...