Homework Answers
Add Answer to:
Question 1) Determine the required number of active coils and permissable deflection in a helical spring...
For a helical compression spring with 20 active coils made from 10 gage, oil-tempered A229 steel...
For a helical compression spring with 20 active coils made from 10 gage, oil-tempered A229 steel wire, use metric units to determine the spring rate and the shear stress at a deflection of 25 mm. The spring index is 5. Is it safe?
2. A helical compression spring is made from No. 8 steel wire and is to carry a 100 lb static load at a deflection of 1 inch. The outside coil diameter of the spring is 0.972 inches. The spring ends...
2. A helical compression spring is made from No. 8 steel wire and is to carry a 100 lb static load at a deflection of 1 inch. The outside coil diameter of the spring is 0.972 inches. The spring ends are squared. Assume the torsional yield strength of the wire is 80000 psi, and the shear modulus is 11.4 Mpsi, determine (a) The static load corresponding to the yield strength. (b) The deflection that would be caused by the load...
2. A helical compression spring is to be designed as shown in Fig Q2. The spring is required to exert a force of...
2. A helical compression spring is to be designed as shown in Fig Q2. The spring is required to exert a force of Po-102 N when compressed to a length of lo=44 mm. When its length is 1=76 mm, it must exert a force of P=22 N. The spring will be cycled rapidly, with severe service required. Use ASTM A401 steel wire. The factor of safety, η, need to be larger than 1.5. Starting with a spring index of 9,...
2. A helical compression spring is to be designed as shown in Fig Q2. The spring is required to exert a force of...
2. A helical compression spring is to be designed as shown in Fig Q2. The spring is required to exert a force of Po-102 N when compressed to a length of lo-44 mm. When its length is I-76 mm, it must exert a force of P-22 N. The spring will be cycled rapidly, with severe service required. Use ASTM A401 steel wire. The factor of safety, η, need to be larger than 1.5. Starting with a spring index of 9,...
Question 6 A composite spning has two close-coiled helical springs in series One spring is made...
Question 6 A composite spning has two close-coiled helical springs in series One spring is made of steel with a mean coil diameter of 15 mm, wire diameter 15 mm and has 10 coils The other spring is made from bronze with a mean coil diameter of 20 mm and wire diameter of 2 mm and B coils Calculate 61 The stiffness of the composite spring, 62 The greatest load that can be camned by the composite spring of the...
QUESTION 1 A compression coil spring made of an alloy steel is having the following specifications:-...
QUESTION 1 A compression coil spring made of an alloy steel is having the following specifications:- Mean diameter of coil = 50 mm; Wire diameter = 5 mm; Number of active coils = 20; If the spring is subjected to an axial load of 164 N. Calculate the maximum shear stress (Neglect the curvature effect) to which the spring material is subjected. (units of MPa).
1. A closely coiled helical spring made of 15 mm diameter steel wire has 15 coils...
1. A closely coiled helical spring made of 15 mm diameter steel
wire has 15 coils of 110 mm mean diameter. The spring is subjected
to an axial load of 180 N. Calculate the maximum shear stress
induced in the spring. Assume modulus of rigidity is 78 GPa.
2. A solid circular bar ABC consists of two segments, as shown
in the figure. One segment has diameter d1= 65 mm and
length L1 = 1.54 m; the other segment has...
A close-coiled helical spring has a mean coil diameter 120 mm. A load of 4 kN...
A close-coiled helical spring has a mean coil diameter 120 mm. A load of 4 kN causes a deflection of 50 mm and a maximum stress of 500 MPa. Calculate 4.1. a) The wire diameter b) The number of coils c) The energy absorbed when subjected to the maximum load d) The spring stiffness 4.2. By use of a clearly labelled neat sketch, show that the deflection in a close-coiled 12] where Wis ; where W is the axial load...
Design a helical compression spring subjected to a varying axial force of 1000 N to 2000...
Design a helical compression spring subjected to a varying axial force of 1000 N to 2000 N, is made of circular steel wire. Over this force range, the deflection of spring should be approximately 5 mm. Consider spring index = 5, for the spring that has square and ground ends. The spring is made of patented and cold drawn steel wire of grade 1 with A and m = 1753 and 0.182 respectively. The permissible shear stress for the spring...
1) [60 pts] Helical Compression Spring A helical compression spring is wound using music wire of...
1) [60 pts] Helical Compression Spring A helical compression spring is wound using music wire of diameter, d, 2.64 mm. The spring has an outside diameter, OD, of 33 mm with plain ground ends and 14 coils. a) Estimate the spring rate. The spring rate is N/mm. b) What is the force needed to compress this spring to closure assuming that the spring will reach its shear strength at its solid length? The force needed to compress this spring to...
2. A helical compression spring is made from No. 8 steel wire and is to carry a 100 lb static load at a deflection of 1 inch. The outside coil diameter of the spring is 0.972 inches. The spring ends are squared. Assume the torsional yield strength of the wire is 80000 psi, and the shear modulus is 11.4 Mpsi, determine (a) The static load corresponding to the yield strength. (b) The deflection that would be caused by the load...
2. A helical compression spring is to be designed as shown in Fig Q2. The spring is required to exert a force of Po-102 N when compressed to a length of lo=44 mm. When its length is 1=76 mm, it must exert a force of P=22 N. The spring will be cycled rapidly, with severe service required. Use ASTM A401 steel wire. The factor of safety, η, need to be larger than 1.5. Starting with a spring index of 9,...
2. A helical compression spring is to be designed as shown in Fig Q2. The spring is required to exert a force of Po-102 N when compressed to a length of lo-44 mm. When its length is I-76 mm, it must exert a force of P-22 N. The spring will be cycled rapidly, with severe service required. Use ASTM A401 steel wire. The factor of safety, η, need to be larger than 1.5. Starting with a spring index of 9,...
Question 6 A composite spning has two close-coiled helical springs in series One spring is made of steel with a mean coil diameter of 15 mm, wire diameter 15 mm and has 10 coils The other spring is made from bronze with a mean coil diameter of 20 mm and wire diameter of 2 mm and B coils Calculate 61 The stiffness of the composite spring, 62 The greatest load that can be camned by the composite spring of the...
QUESTION 1 A compression coil spring made of an alloy steel is having the following specifications:- Mean diameter of coil = 50 mm; Wire diameter = 5 mm; Number of active coils = 20; If the spring is subjected to an axial load of 164 N. Calculate the maximum shear stress (Neglect the curvature effect) to which the spring material is subjected. (units of MPa).
1. A closely coiled helical spring made of 15 mm diameter steel
wire has 15 coils of 110 mm mean diameter. The spring is subjected
to an axial load of 180 N. Calculate the maximum shear stress
induced in the spring. Assume modulus of rigidity is 78 GPa.
2. A solid circular bar ABC consists of two segments, as shown
in the figure. One segment has diameter d1= 65 mm and
length L1 = 1.54 m; the other segment has...
A close-coiled helical spring has a mean coil diameter 120 mm. A load of 4 kN causes a deflection of 50 mm and a maximum stress of 500 MPa. Calculate 4.1. a) The wire diameter b) The number of coils c) The energy absorbed when subjected to the maximum load d) The spring stiffness 4.2. By use of a clearly labelled neat sketch, show that the deflection in a close-coiled 12] where Wis ; where W is the axial load...
1) [60 pts] Helical Compression Spring A helical compression spring is wound using music wire of diameter, d, 2.64 mm. The spring has an outside diameter, OD, of 33 mm with plain ground ends and 14 coils. a) Estimate the spring rate. The spring rate is N/mm. b) What is the force needed to compress this spring to closure assuming that the spring will reach its shear strength at its solid length? The force needed to compress this spring to...
Most questions answered within 3 hours.
-
Calculate the pH of each of the following solutions.
0.50 M HBr
3.1×10−4 M KOH
4.2×10−5...
asked 25 minutes ago -
For the year ended December 31, Depot Max’s cost of merchandise
sold was $85,600. Inventory at the...
asked 25 minutes ago -
Week 10 - Professional Memo Assignment
Professional Memo Assignment
Your mission for this week, should you...
asked 30 minutes ago -
Write a Python program that stores the data for each
player on the team, and it...
asked 40 minutes ago -
In
the last 3 months, mike never knows when he is going to get his
allowance...
asked 1 hour ago -
Is Ca(OH)2 a Bronsted base, Lewis base, or both? Why?
asked 54 minutes ago -
1A- Why don’t voters complain about U.S. tariffs on imported
sugar?
Because sugar is only a...
asked 1 hour ago -
Cash Payback Period
Primera Banco is evaluating two capital investment proposals for
a drive-up ATM kiosk,...
asked 1 hour ago -
Create a button in Swift (Xcode) that will create a charge,
create a charge using Stripe's...
asked 1 hour ago -
The reaction rate of CO and NO2 in the reaction
CO(g) + NO2(g) → CO2(g) +...
asked 1 hour ago -
Imagine that a chemist puts 6.40 mol each of
C3H8 and O2 in a 1.00-L container...
asked 1 hour ago -
How much money should be invested today in order to have $8340
at the end of...
asked 1 hour ago