As shown in the following figure, the speed of a 12 kW, 220 V, 1000 rpm...
solve it now please A 220 V, 1000 rpm, separately excited dc motor is fed from a three-phase controlled three-phase ac-dc converter through 220 V (line value-rms value), 50 Hz ac-source. It is required to apply 220 V (dc-value) across the motor terminals. What is the firing angle if the motor speed is 1000 rpm and takes 10 A ripple-free current. The armature resistance is 1 ohm. The field circuit with 198 ohms is fed from a fully controlled single-phase...
Open Book Exam A 220 V, 1000 V dc-sourc rpm, separately dc motor is fed from a dc-dc converter through 550 e with duty cycle 40 %. The motor speed is 1000 rpm when takes ripple free and armature resistance is 1 Ω. The motor constant is 6/π V/A-rad/s. The field circuit with 198 Ω is fed from a controlled single-phase rectifier and set to the maximum possible value. The ac source for field circuit is 220 V, 50 Hz....
6. The speed of a 150 HP, 650 V, 1750 rpm, separately excited DC motor is controlled by a 3- phase full converter. The converter is operating from 3-phase, 460 V, 50 Hz supply. The rated armature current of the motor is 170 A. The motor parameters are Ra = 0.099 2, La = 0.73 mH, and K.D=0.33 V/rpm. Neglect the losses in converter system. Determine i. No-load speed at firing angles a = 0º and a = 30°. Assume...
4. A 3-phase full-wave converter drive is feeding power to a 220 V, 20 A, 1000 rpm separately excited dc motor. The ac input to the converters are 415 V, 3-phase, 50 Hz, Y-connected supply system. The field is also controlled by a 3-phase full converter and is set to the maximum possible value. The armature resistance is 0.5 Q and the field resistance is 250 12. The motor voltage constant is 1.2 V/A rad/s. Assume continuous conduction and ripple...
Q2. (10 points) A 10 kW, 100 V, 1000 rpm dc shunt generator has armature resistance Ra = 0.1.2. The field current generating 100 V at no-load is 1.0 A. The magnetization characteristic at 1000 rpm is shown in figure below. The machine is operated as a separately excited dc generator at 1000 rpm with rated field current. Neglecting the armature reaction effect; (a) Determine full load armature current, la (b) Determine the terminal voltage at full load, with ly...
i. The speed of a separately excited dc motor is controlled by a one-phase full-wave converter. The field circuit is also controlled by a full-wave converter, see V supply) Vs pk-150V Ra-0.310 L Rf 152O E-63V α. 1-35A Figure 3 The AC supply voltage to the armature and field converters is one-phase, 150Vpeak, 50Hz. The armature resistance Ra-0.31Ω, the field circuit resistance Rf-152Ω, and the motor voltage constant is Kv-1.3V/A. The armature current corresponding to the load demand la-35A The...
A power electronic converter used to drive a separately-excited DC motor for application in Sohar, Oman as shown in Figure Q2. Let R = 0.25 , K = 0.62 V/rpm.Wb, (flux per pole) = 175 mWb. The used converter is a single-phase, controlled full-wave bridge rectifier. Assume the firing angle is 45°, and the average speed is 1300 rpm and torque constant K is 9.55 of K. Assuming the motor current is continuous; calculate the armature current drawn by the...
7. An 80 kW, 440 V, 800 rpm DC motor is operating at 600 rpm and developing 75% rated torque is controlled by 3-phase, six-pulse thyristor converter. If the back emf at rated speed is 410 V, determine the triggering angle of the converter. The input to the converter is 3-phase, 415 V, 50 Hz ac supply.
Question (3) Speed Control [10 Marks A 50 hp, 220 V, 1500 rpm DC shunt motor with an armature resistance of 0.04 Q and a field resistance of 50 Q. The motor has compensating windings, so armature reactance can be ignored. Mechanical and core losses may be ignored also. The moter is driving a load toque that is proportional with speed, Ti a (n). The motor is driving a load with a line current of 80 A and an initial...
3) A saperately excited DC motor has the following parameters: Ra = 10 Ke = 0.4 V/rpm. Wb O = 0.2 Wb The motor speed is controlled by a full-wave bridge rectifier. The firing angle is set at 45, and the average speed is 1500 rpm. The applied AC voltage to the input of the bridge rectifier is 220Vrms - 50 Hz. a) (10p) Please draw the complete circuit. (converter + motor) b) (10p) Please find the armature current. c)...