What is the molecular weight of the 2 isomers made from the chlorination of 2,3-dimethylbutane, using 35Cl and 37Cl. the products incase you need them are 2-chloro-2,3-dimethylbutane and 1-chloro-2,3-dimethylbutane. show work please
What is the molecular weight of the 2 isomers made from the chlorination of 2,3-dimethylbutane, using...
1) Write the mechanism of chlorination reaction of the following compounds and draw the constitutional isomers a) Butane b) 2-methylbutane c) methylcyclobutane d) 2.2-dimethylbutane 2) An alternative reaction of ethane chlorination is shown below a) Why does not this reaction occur? b) Show a mechanism for this alternative reaction 3) Write the mechanism for the formation of carbon tetrachloride from methanelighthv. 1) Write the mechanism of chlorination reaction of the following compounds and draw the constitutional isomers a) Butane b)...
Two constitutional isomers have a molecular weight of 58 g/mol. The IR of one isomer shows a strong absorption band at 1740 cm 1, while the other isomer shows a strong absorption band at 3450 cm". Identify the two compounds --Show your work below. 2.
A Freezing-Point Depression experiment is done using 2 different test tubes to find the molecular weight of an unknown mixture. Tube 1 consists of pure Lauric acid, and Tube 2 consists of Lauric acid + an unknown solute mixture. From the calculations of this experiment, the molecular weight of the unknown acid can be found. A) How would the loss of some Lauric acid from Test Tube 1 have affected the calculation of a molecular weight? Would the calculated molecular...
1-Calculate the molecular weight of the repeat unit (monomer) for polystyrene (above) (2 marks) 2-Using the table below, calculate the degree of polymerisation for polystyrene Molecular weight range (g/mol) Number fraction,xi 500-1000 0.02 1000-3000 0.13 3000-5000 0.25 5000-10000 0.41 10000-25000 0.15 25000-50000 0.04 3-Which crystal type would be expected for Nickel Oxide (NiO, Ni2+ ionic radius = 0.069nm, O2- ionic radius = 0.14nm) (2 marks) 4-In order to save weight, a composite component is to be made of aligned fibreglass...
We made esters from carboxylic acids and alcohol. (for one of them, acetic acid + isopentyl alcohol + couple drops of sulfuric acid). Could someone please explain those. Thank you 1. Consider if we had prepared high molecular weight esters, what problems would this pose regarding our method of analysis 2. We used sulfuric acid as a catalyst, but carboxylic acids are a reagent in this reaction. Would simply using excess carboxylic acid work as efficiently as sulfuric acid to...
1. (4 points) Given that the average molecular weight of an amino acid is 110 daltons (Da), determine the following. Remember to convert between daltons and kilodaltons (kDa) where necessary. Each of your answers must be numerically correct and expressed in proper units (1 pt) and show how the value was arrived at using the amino acid molecular weight above (1 pt) for you to receive full credit. A. A molecule of human a-tubulin has a molecular weight of 50.1...
1. For the earth, an estimate of the variation of pressure with altitude above the surface of the earth is made for a gas of molecular weight, M, assuming the atmosphere is isothermal, the variation of g with altitude is negligible, and that the atmosphere behaves like an ideal gas. A significant error in this estimate arises from the assumption that the temperature of the atmosphere, T, is isothermal instead of decreasing with altitude. This decrease with altitude y in...
1. Using the reaction of 2-chloro-1-methylcyclohexane with hydroxide ion, give the mechanism of Sn1 substitution. Complete the question as in question 1 2. Show how you might synthesise the following compounds given the indicated starting materials and anything else you need. In other words, show the reactions that would lead from starting materials to products. Assume that you can purify the products of each reaction. A synthesis may require more than one reaction (products of one reaction are used as starting materials in the...
Week 10- Constitutional isomers Constitutional isomers have the same molecular formula, but their atoms are bonded in different orders. These may be further distinguished as chain isomers, which differ only in hydrocarbon chain structure, positional isomers, which differ in the location of a functional group, and functional group isomers which differ in the nature of their functional groups. Typically chain and position isomers show only modest differences in their physical and chemical properties, while functional group isomers differ greatly from...
1. Molecular cloning has made it possible to take a DNA fragment from nuclear DNA, containing an entire gene, and insert it into a cloning plasmid just behind a phage promoter. This means that the cloned gene can be transcribed in a test tube using a commercially available phage RNA polymerase protein. If you were to use agarose gel electrophoresis to separate RNA according to size, would the RNA produced in the test tube show any differences with RNA from...