Question 1 (20 marks) Consider the circuit in Figure Q1. Ri WW R2 6T OB Figure...
0.2500 62 5 + 20 +18 V Given a complex circuit in Figure Q1. This complex circuit is to be viewed in a simpler form of Thevenin and Norton equivalent circuits a) Dengan menggunakan analisis nod, cari voltan Thevenin, Vrh di terminal a dan b. By applying Nodal analysis, find Thevenin voltage, Vru al terminal a and b. (4 markah/marks) b) Sekiranya terminal a dan b dibiarkan bersambung, tentukan nilai semasa arus yang melalui terminal tersebut, iaitu Isc. Berikutan itu,...
Q1. (3 marks) In the circuit shown below, R-1.5KO and the voltage drop across Ri is 4.5V. (1 pt.) A. What is the voltage drop across R? (1 pt.) B. What is the value of the resistance R? (1 pt.) C. What is the power delivered by the source voltage? S Answer: wwiw R Ri Vs=15V Q2. (3 marks) Refer to the circuit below. A. Using the voltage divider law, find the voltage between the points A and B. B....
Problem #1: Circuit Analysis and Thevenin Equivalent [20 points] The bridge circuit is connected to a load RL between terminals (a, b) as shown (a) Use node-voltage method to solve for VTH respect to terminal (a, b) (b) Use mesh-current method to solve for isc respect to terminal (a, b) 5Ω 2Ω 2 Ri b al 16 V 4Ω 2Ω
b) For the circuit shown in Figure Q1(b) below, the voltage source is 18 V. Determine Vo, Voz and /. [CO2/PO3/C4] (10 marks) Vo1 0.47 k 1 ka Vo2 Si 18 V Si Figure Q1(b) For the circuit shown in Figure Q1(b) below, the voltage source is 18 V. Determine b) Vot, Voz and / [CO2/PO3/C4] (10 marks) Vof 1 ka 0.47 kn Vo2 ZSI 18 V Figure Q1(b) ) Figure Q1(c) shows a basic voltage regulator circuit. Determine Vi,...
C.la For the circuit of Figure 1, choose values for resistors R1, R2, and R3(all resistances must be greater than one Kilo ohm). Given that the voltage source Vs1 = 8V and Vs2 = 10V determine the output voltage Vout. C.1b For the same resistor values Ri, R2, and Rs you chose in part C.la Given that the voltage source Vsi = 8V and Vs2 = 10V, use Figure 2(a) to determine the output voltage Vout/ and Figure 2(b) to determine the output voltage Vout2. Discussion:...
For the circuit in Figure 1, you need
to calculate the current I2 and the voltage
across the current source. (10 marks).
B1. For the circuit in Figure 1, you need to calculate the currently and the voltage across the current source. (10 marks). R2 = 6.222 12 R 512 R4 8.212 2.5 A R3 34.7.12 E 10 V
The circuit shown has four unspecified circuit parameters: vs. R1, R2, and d, where d is the gain of the CCCS. To design this circuit, we must specify the values of these four parameters. The graph shown describes a relationship between the current i and the voltage v. Specify values of vs. Ri, R2, and d that cause the current i and the voltage y to satisfy the relationship described by the graph. Hint: The equation representing the output voltage...
Problem 1 (20 %) We want to analyse an electrical circuit described as a 2-port (Figure ). The circuit has source terminal with a constant ideal voltage source Vs and a loading terminal with a loading resistor Ri. Circuit with passive components Figure 1. General electric circuit We want to represent the circuit as seen from the loading terminal as a Thevinin and a Norton equivalent. Sketch these crt equivalents and describe the steps how to determine their component values....
Analyze the following circuit with
R1=1.0 kΩ
R2=1.2 kΩ :
a) Apply ohms law to find I3. (Enter answer in mA with 3
decimals)
b) Calculate the power dissipated in R2, Express your answer in
mW with 3 decimals,
c) Apply KCL at node x to determine I2. Enter your answer in mA
with 3 decimals.
d) Calculate the power supplied or absorbed by the voltage
source. Express your answer as a signed mW value to 3 decimals.
e) Apply...
1 The resistors Ri and R2 form a circuit called a "voltage divider Ground:V- For this circuit: a. What is the equivalent resist ance of the combination Ri and R2? b. What is the current in the circuit? c. What is the voltage drop across the resistor Ri? d. What is the voltage at the point A? e. What choice of Ri and R2 would give a voltage at point A equal to 6 volts?