6 6. (7 pts) Determine the voltage at the output node for the circuit below, The...
Please help me asap Consider the difference amplifier circuit below. a. (8 pts) Determine the difference-mode gain Ad in dB. In1 1K 20K U1 Output In2 1K Answer 20.1K b. (8 pts) Determine the common-mode gain Acm in dB Answer For the circuit below, use the constant voltage drop diode model with vo-0.7 a. (12 pts) Determine the states (on or off of DI and D2. D2 1k lk 1K D1 D1 Answer: D2 Answer (6 pts) Determine the voltage...
2. (4+6) Determine the output voltage Vout for the circuit below assuming the VCVS gain a. b. (4+6) Repeat part (a) with the op amp open loop gain A = 100. R1 R2 10K ·out 2K R3 1K 100 4 2. (4+6) Determine the output voltage Vout for the circuit below assuming the VCVS gain a. b. (4+6) Repeat part (a) with the op amp open loop gain A = 100. R1 R2 10K ·out 2K R3 1K 100 4
1. For the 4 circuits shown below, sketch the output waveform for a 1V peak, 1kHz, sinusoidal wave in put signal. Assume the diodes are ideal and they exhibit ON-OFF switch model behaviour. Create an ideal diode model in LT-Spice with the following specification [.model IdealDiode D(Ron=0.1m Roff=100G Vfwd-0.0) ] simulate the circuit and verify the output waveform. Vin Vout Vin Vout 1k 1k (a) (b) 1k Vin 1k Vin Vout Vout ww 1k (c) (d) KH 1. For the...
5. Evaluate the circuit below. Calculate the node voltage Vn. Assume the diodes are ideal 2K.a IKaIkn 4V
12. Determine the output voltage (V.) of the below amplifier circuit. Vo= 18 ΚΩ 6 ΚΩ 36 ΚΩ 6 ΚΩ 1 2V(+). 12 ΚΩ (E) 1ν ΛΛΑ- 12 ΚΩ 3V
For this problem, you may assume that the operational amplifier is ideal. For the circuit below, find the output voltage Vout, given R1 = 1k ohms, R2 = 4k ohms and Vs = 1V. OUT Select one: O a.- 0 6.5 c. 1.25 d. -4 O e. -0.75
3. (imts) Determine the node voltage va, v, and ve for the circuit shown below. Assume ideal OP Amp 10 ㏀ +)12 V 40 ㏀ 15 k2
Please select the correct statements: The bandwidth of a circuit can be found by measuring the 5/7 drop in output signal The input impedance of a circuit can be found by adding a resistor in parallel and measuring the change in voltage The X-Y mode on the scope shows the phase difference and distortion between two inputs E12 resistors have +/-10% tolerence. Typical values are: 100, 1k, 1.5k, 2k Ohm An voltage follower op-amp with a slew rate of 1V/ms...
For the fullwave rectifier circuit shown below, the input voltage is Vi 6 sin 2n60t and the diodes D1, D2, D3, D4 each have a forward- voltage drop of 0.7 V when conducting. Determine the average value of the output voltage Vo (in V). (Enter your answer as a number without the units.)
electronics electronic Diode e ce m An amp Ain dn None the s0d r n A-3.De e po are Consider the eireait below using an ideal op amp 8 pta) Determine the voltage at Node 2 sode3 azv Anewer b (12 pts) Determine the value ofR that sets the voltage at Node3 to +9 V. Answer (8 pts) Assume the voltage at Node3 is +9V. Determine the magnitude of the current in the 10 k2 resistor. Answer Answer Node2 Consider...