Question 2(b) A 0.6 cm thick rectangular plate is pulled in tension by two loads in...

Question

Question

Question 2(b) A 0.6 cm thick rectangular plate is pulled in tension by two loads in the x and y directions as shown in Figure

Answer 1

Answer #1

P, 20 Pa = SUN Sanxo.6 cm 3 cm² = 3x10 m² Р. sx18 Pa A Зх то Py = akn A = 10 cm * 0.6 m в хоч » , 20 Pa Ру 3 x 107 Pa 2 МА А

Answer 2

Similar Homework Help Questions

A plate 92 mm wide, 184 mm long, and 11.04 mm thick is loaded in tension...

A plate 92 mm wide, 184 mm long, and 11.04 mm thick is loaded in tension in the direction of the length. The plate contains a crack as shown in the figure below with the crack length of 147 mm. The material is steel with KC = 80 MPa (my(12) and Sy=950 MPa. 7.0 6.0 3.0 40 10 /b=05 1.0 2.0 10 02 0.6 0.8 w/braio Ignoring stress concentration, determine the maximum possible load that can be applied to the...
A plate 90 mm wide, 180 mm long, and 10.8 mm thick is loaded in tension...

A plate 90 mm wide, 180 mm long, and 10.8 mm thick is loaded in tension in the direction of the length. The plate contains a crack as shown in the figure below with the crack length of 14.4 mm. The material is steel with Kic= 80 MPa (m)(12) and Sy =950 MPa. 7.0 6.0 5.0 4.0 3.0 h/b=0.5 1.0 2.0 1.0 0.2 0.6 0.8 0.4 a/b ratio Determine the maximum possible load before the plate has uncontrollable crack growth....
A plate 125 mm wide, 250 mm long, and 12 mm thick is loaded in tension...

A plate 125 mm wide, 250 mm long, and 12 mm thick is loaded in tension in the direction of the length. The plate contains a crack as shown in Figure 5-26 (textbook) with a crack length of 31 mm. The material is steel with Kıc = 70 MPa.mo.5 and Sy= 950 Mpa. Determine the maximum possible load that can be applied before the plate has uncontrollable crack growth. a. 202 kN b.314 KN c. 283 kN d. 165 kN...

A plate 125 mm wide, 250 mm long and 12 mm thick is loaded in tension...

A plate 125 mm wide, 250 mm long and 12 mm thick is loaded in tension in the direction of the length. The plate contains a crack as shown in Figure 5-26 (textbook) with a crack length of 31 mm. The material is steel with KIC - 70 MPa.m0.5 and Sy - 950 Mpa. Determine the maximum possible load that can be applied before the plate has uncontrollable crack growth. 2.314 KN b.283 KN OC 202 KN d. 165 KN...
The rectangular plate shown in the figure below has the given loads uniformly distributed over the...

The rectangular plate shown in the figure below has the given loads uniformly distributed over the edges. The plate is 50 mm thick, AB is 500 mm and BC is 400 mm (a) (b) (c) (d) (e) Determine the shear forces which must operate on the edges BC and DA to maintain the equilibrium of the plate Relative to the x,y reference axes, determine the state of stress at any point P in the interior of the plate For the...
A uniform load Po acts on a long and narrow rectangular plate with edges at y 0 and y b both clamped as shown in figure...

A uniform load Po acts on a long and narrow rectangular plate with edges at y 0 and y b both clamped as shown in figure Q 4b below. For Po 20 kN/m, b 0.6 m, t 12 mm, E 200 GPa, and v 0.333. Determine the maximum -deflection of the plate (6.5 Marks) b A uniform load Po acts on a long and narrow rectangular plate with edges at y 0 and y b both clamped as shown in...

A plate 95 mm wide, 190 mm long, and 11.4 mm thick is loaded in tension...

A plate 95 mm wide, 190 mm long, and 11.4 mm thick is loaded in tension in the direction of the length. The plate contains a crack as shown in the figure below with the crack length of 15.2 mm. The material is steel with KIC= 80 MPa (m)(1/2) and Sy= 950 MPa. 6.0 5.0 4.0 3.0 h/b=0.5 1.0 2.0 1.0 0.2 0.4 a/b ratio Ignoring stress concentration, determine the maximum possible load that can be applied to the plate...
A plate 92 mm wide, 184 mm long, and 11.04 mm thick is loaded in tension...

A plate 92 mm wide, 184 mm long, and 11.04 mm thick is loaded in tension in the direction of the length. The plate contains a crack as shown in the figure below with the crack length of 14.7 mm. The material is steel with Kic=80 MPa (m) (121 and Sy=950 MPa 7.0 6.0 5.0 4.0 3.0 1/b=0.5 1.0 2.0 10 OB 04 06 ON wibratio Determine the maximum possible load before the plate has uncontrollable crack growth. The maximum...
A plate 92 mm wide, 184 mm long, and 11.04 mm thick is loaded in tension...

A plate 92 mm wide, 184 mm long, and 11.04 mm thick is loaded in tension in the direction of the length. The plate contains a crack as shown in the figure below with the crack length of 14.7 mm. The material is steel with KC= 80 MPa (m)(1/2) and Sy=950 MPa 7.0 6,0 5.0 4.0 3.0 /b=0.5 1.0 20 LO 0 02 06 OX 04 w/bratio Ignoring stress concentration, determine the maximum possible load that can be applied to...

A plate 125 mm wide, 250 mm long and 14 mm thick is loaded in tension...

A plate 125 mm wide, 250 mm long and 14 mm thick is loaded in tension in the direction of the length. The plate contains a crack as shown in Figure 5-26 (textbook) with a crack length of 25 mm. The material is steel with Kic - 30 MPa.mQS and Sy- 950 Mpa. Determine the maximum possible load that can be applied before the plate has uncontrollable crack growth. a. 201 357 6.417 d. 124 .229