Question 8 Given below is the block diagram of gas chromatography. Identify the unmarked component. Column...

Question

Question

Answer 1

Answer #1

The block diagram is of gas chromatography system and the unlabeled part is sample injection system which is present just before the column.

Hope you will like my answer.

Answer 2

Similar Homework Help Questions

Question) The transfer function of the system given in the block diagram below a) Find with...

Question) The transfer function of the system given in the block diagram below a) Find with the block diagram reduction method? b) Find by Routh-Hurwitz stability analysis method? NOTE: Draw option b on the flow diagram and solve it. R(S) C(s) GA G3 G H
The heavier component has to be removed from a gas stream by absorption. The absorption column...

The heavier component has to be removed from a gas stream by absorption. The absorption column operates at 2 550 kPa. The entering liquid is high molecular mass oil which contains 0.45% of the heaviest component but none of the lighter components. The total molar flowrate of the oil entering the absorber is 150 kmol/hr. The effluent gas that enters the absorber at 800 kmolhr contains 20 mol% C, 46 mol% C2, 30 mol% C3, 4 mol% n-C4. There are...
Question 13 A block diagram of MIPS architecture is given below. What is the value of...

Question 13 A block diagram of MIPS architecture is given below. What is the value of the control bit for each MUX during the execution of the given instruction? Note, you may use N/A MUX output is not Instruction MUX 1 MUX 2 MUX 3 MUX 4 Iw RL, 8(2) add R1, R2, RS ori R1, R2, 15 bne R1, R2, loop (Branch is not taken)

Question 28 1 points Given below is a diagram of separation of two components of a...

Question 28 1 points Given below is a diagram of separation of two components of a mixture in a chromatographic column. From the diagram inter which component has lesser afinity to the stationary pha Mobile phase Component w Component Component Component Component X Component z Component Y 0 0 NT & E 0 0 0 O All the above Question 29 Select the incorrect statement from the following options The spots of colorless compounds are invisible to the eyes The...
2. The diagram below shows the results of a simple thin layer chromatography experiment. height reached...

2. The diagram below shows the results of a simple thin layer chromatography experiment. height reached by the solvent the "solvent font a) Describe briefly, but precisely, what you would have done in order to get to this stage. You can assume that you have been given a suitable thin layer chromatography plate. b) Why is there a cover on the beaker? c) In order to help identify the things in a chromatogram, you can measure the Rf value for...
Question 10 10 pts The block diagram of a feedback control system is shown below. Given...

Question 10 10 pts The block diagram of a feedback control system is shown below. Given a=2.2, b=3, c=2.1, H=5 above which value of K will the system become unstable? R(S) к 1 C(s) S + a S2 + b + c

Find the transfer function for the given block diagram as shown in figure below by using...

Find the transfer function for the given block diagram as shown in figure below by using block reduction rules. (5 Marks) DG-600GBG 10 Fig.5 Explain the liquid level system with block diagram useful in nlaces where it is difficult to monitor
1. A mixture of four alkenes (1-decene, 1-heptene, 1-nonene, and 1-octene) was analyzed by gas chromatography....

1. A mixture of four alkenes (1-decene, 1-heptene, 1-nonene, and 1-octene) was analyzed by gas chromatography. Below, on the line, list the four alkenes in order of increasing retention time: 2. At 760.0 mm atmospheric pressure, a binary liquid mixture of components A and B gives the temperature composition diagram shown below. The liquid curve plots boiling point vs. composition of the liquid mixture. The vapor curve plots temperature vs. equilibrium vapor composition. A horizontal line on the diagram, such...
A block diagram of MIPS architecture is given below. What is the value of the control...

A block diagram of MIPS architecture is given below. What is the value of the control bit for each MUX during the execution of the given instruction? Note, you may use N/A if MUX output is not useful. Instruction MUX 1 MUX 2 MUX 3 MUX 4 lw R1, 8 (R2) add R1, R2, R3 ori R1, R2, 15 bne R1, R2, loop (Branch is not taken)

The problem states, “Given the block diagrams below, draw the logic circuit diagram for part 1.” Given the block diagrams below, draw the cireuit diagram for part 1. Vce 16 15 10 14 13 74LS48 12...

The problem states, “Given the block diagrams below, draw the logic circuit diagram for part 1.” Given the block diagrams below, draw the cireuit diagram for part 1. Vce 16 15 10 14 13 74LS48 12 10 GND Numerical Designations-Resultant Displays LT RB HHHLLHH LLHH LHL Given the block diagrams below, draw the cireuit diagram for part 1. Vce 16 15 10 14 13 74LS48 12 10 GND Numerical Designations-Resultant Displays LT RB HHHLLHH LLHH LHL