answer: elev. tank 2=1426.6 ft, Q=4.96cfs
answer: elev. tank 2=1426.6 ft, Q=4.96cfs Q4. For the system below calculate the elevation in tank...
Problem 3 A pipeline delivers water from Reservoir 1 to Reservoir 2 as shown in the following figure. The water levels at Reservoirs 1 and 2 are 50 ft and 20 ft, respectively. A globe valve is installed in the pipeline with a minor head loss coefficient k 10. The pipe from Reservoir 1 to the globe valve is 1000 ft long and 6 inches in diameter. The pipe from the globe valve to Reservoir 2 is also 1000 ft...
1. A pipeline with a pump from Tank A leads to a nozzle that discharges by cascade into Tank B. Tank 8 is located 10 ft above Tank A. What is the flow rate when the pump adds a head of 80 ft. Assume the head loss in the 6 ft suction pipe can be described by hy-5V-/2g, while the head loss in the 4 inch pipe can be described by 12V?/2g. Sketch the hydraulic grade line and the energy...
Fig. Q4 shows a piping arrangement used in a food processing facility to transfer water, at 40 C, from a tank, through a heat exchanger to an elevated tank. A suitable pump is selected which, when installed, delivers the water at 2.5 m'/hr. The pipe diameter is 40 mm and the Absolute Roughness of the pipe material is 0.00008 m. The Loss Coefficients [K Factors] for the Bend and Heat Exchanger are shown in Fig. Q4 4. 2 m K...
Please help asap with this one In the system below, water is being pumped from the lower reservoir to the upper reservoir. The pipe diameter, pipe length, flowrate and total system head losses are shown on the sketch. Determine the head added by the pump. Assume the losses are uniform along the length of the pipe. Sketch the approx energy grade line. Elev. 132.0 ft Frictional head losses in the pipe are 27.36 ft. Water -Elev. 97.5 Ft Water Q...
A turbo pump transfers water from tank 1 to tank to tank 2 as shown in the picture below. The diameter of the piping system is D= 4in and the total length of pipes is L=620 ft. the elevation difference is Z1-Z2= 30ft. Use the chart for KL values. a) determine the flow rate (Q) b) power of the pump in HP Note that you can write out both mass balance equation and energy equation of the head form for...
A turbo pump transfers water from tank 1 to tank to tank 2 as shown in the picture below. The diameter of the piping system is D= 4in and the total length of pipes is L=620 ft. the elevation difference is Z1-Z2= 30ft. Use the chart for KL values. a) determine the flow rate (Q) b) power of the pump in HP Note that you can write out both mass balance equation and energy equation of the head form for...
A pump transports water from Tank 1 to Tank 2 through a constant-diameter piping system as shown below (not to scale). The flow rate is controlled by two gate valves, the gate valve I controls the main pipeline, while the gate valve II controls the loop line from T-joint A to T-joint B. All pipes are galvanized steel pipe of diameter D = 4 in. It has a total length of Li2= 620 ft from tank 1 to tank 2....
3) As shown in the figure below, water (o 1.94 slugs/ ft') is pumped from a large tank (1) at a rate of 3 ft'/s through a main supply line to the top of an aeration column (2), which is a large free surface open to the atmosphere. The head loss through the supply line is 4 ft. In the acration column, the water is entrained with air as it moves downward via gravity through the column and exits to...
10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated sludge operation that adversely affect effluent quality with origins in the engineering, hydraulic and microbiological components of the process. The real "heart" of the activated sludge system is the development and maintenance of a mixed microbial culture (activated sludge) that treats wastewater and which can be managed. One definition of a wastewater treatment plant operator is a "bug farmer", one who controls the aeration...