Homework Answers
Add Answer to:
A one-third scale model of a car is to be tested in a wind tunnel. The...
The aerodynamic characteristics of a new car are to be predicted through a wind tunnel testing....
The aerodynamic characteristics of a new car are to be predicted through a wind tunnel testing. Engineers build a one-fifth scale model of the car and placed it in the test section of the wind tunnel. The measured flow properties are given as Modet T+5°C, ?-1269kg/m 3 , ?-1.754 x 10-5 kg/m.s Prototype: T 25°C,p:1184 kg/m, ?#1.849 x 10-5 kg/mS, If the dimensional analysis results are outline as follows: V-50km/h Where, aerodynamic drag force, ? = density, V = speed,...
Automotive engineers plan to build a one-third scale model of a sports car and test it...
Automotive engineers plan to build a one-third scale model of a sports car and test it in a wind tunnel. The temperature of the wind tunnel is at 25°C. The drag force is measured with a drag balance and the moving belt is used to simulate the moving ground. If the sports car runs at 25°C, Wind tunnel test section L Fom Moving belt Drag balance Figure 4 Question 4 a) Propose the speed of the car that can be...
Problem 6: Measurements of drag force are made on a model automobile in a towing tank...
Problem 6: Measurements of drag force are made on a model automobile in a towing tank filled with fresh water. The model length scale is 1/5 that of the prototype. State the conditions required to ensure dynamic similarity between the model and prototype. Determine the fraction of the prototype speed in air at which the model test should be made in water to ensure dynamically similar conditions Measurements made at various speeds show that the dimensionless force ratio becomes constant...
A model of a submarine, 1:15 scale is to be tested at 180ft/s in a wind...
A model of a submarine, 1:15 scale is to be tested at 180ft/s in
a wind tunnel with standard sea-level air, while the prototype will
be operated in sea water.
A model of a submarine, 1:15 scale, is to be tested at 180 ft/s in a wind tunnel with standard sea-level air, while the prototype will be operated in seawater. Determine the speed of the prototype to ensure Reynolds number similarity. Hint: The Reynolds number of the model and prototype...
You are to conduct a wind tunnel testing of a new football design. It is known...
You are to conduct a wind tunnel testing of a new football design. It is known that you need to maintain Reynold’s number, Re, and Strovhal Number, St, similarity for the testing. Based on a standard college quarterback, prototype velocity, V = 40mph and rotation, ω = 300rpm. The prototype football has a diameter of D=7inches. Due to instrumentation requirements, the model used in the wind tunnel must be twice as big as the prototype. Dmodel=14inches. a) Determine the required...
The aerodynamic drag of a new sports car is to be predicted at a speed of 75 km/h at an air temperature of 25°C. Automot...
The aerodynamic drag of a new sports car is to be predicted at a speed of 75 km/h at an air temperature of 25°C. Automotive engineers build a one-fifth scale model of the car to test in a wind tunnel. It is winter and the wind tunnel is located in an unheated building. The temperature of the wind tunnel air is only 5°C. a) Determine how fast the engineers should run the wind tunnel in order to achieve similarity between...
Ex.3 /35 A Cessna 172 has a cruise speed V-226 km/h and weight W-1,000Kg. The wing area is S-16mt...
Ex.3 /35 A Cessna 172 has a cruise speed V-226 km/h and weight W-1,000Kg. The wing area is S-16mt with a wing span b-1lm Assuming the wing rectangular, what is the Reynolds number at an altitude z-1,000m. A model of this airplane, scaled by a factor of 2, is tested in a wind tunnel at sea level. What should be the velocity in the wind tunnel to have dynamics similarity (neglect Mach number effects). What will be the lift measured...
[10 points] A model of a submarine, 1:15 scale, is to be tested at 180 ft/s...
[10 points] A model of a submarine, 1:15 scale, is to be tested at 180 ft/s in a wind tunnel with standard sea-level air, while the prototype will be operated in seawater. Determine the speed of the prototype to ensure dynamic similarity 4. Properties of air: p 2.38x103 slugs/ft3, 3.74 x 107 Ib-s/ ft2 Properties of seawater: 1.99 slugs/ft3JL-2.51 x 10-5 lbs/ ft.
A model test is to be conducted in a water tunnel using a 1: 20 model...
A model test is to be conducted in a water tunnel using a 1: 20 model of a submarine, which is to travel at a speed of 12 km/h deep under sea surface. The water temperature in the tunnel is maintained, so that is kinematic viscosity is half that of sea water. At what speed is the model test to be conducted to produce useful data for the prototype?
A model test is to be conducted in a water tunnel using a 1: 20 model...
A model test is to be conducted in a water tunnel using a 1: 20 model of a submarine, which is to travel at a speed of 12 km/h deep under sea surface. The water temperature in the tunnel is maintained, so that is kinematic viscosity is half that of sea water. At what speed is the model test to be conducted to produce useful data for the prototype?
The aerodynamic characteristics of a new car are to be predicted through a wind tunnel testing. Engineers build a one-fifth scale model of the car and placed it in the test section of the wind tunnel. The measured flow properties are given as Modet T+5°C, ?-1269kg/m 3 , ?-1.754 x 10-5 kg/m.s Prototype: T 25°C,p:1184 kg/m, ?#1.849 x 10-5 kg/mS, If the dimensional analysis results are outline as follows: V-50km/h Where, aerodynamic drag force, ? = density, V = speed,...
Automotive engineers plan to build a one-third scale model of a sports car and test it in a wind tunnel. The temperature of the wind tunnel is at 25°C. The drag force is measured with a drag balance and the moving belt is used to simulate the moving ground. If the sports car runs at 25°C, Wind tunnel test section L Fom Moving belt Drag balance Figure 4 Question 4 a) Propose the speed of the car that can be...
Problem 6: Measurements of drag force are made on a model automobile in a towing tank filled with fresh water. The model length scale is 1/5 that of the prototype. State the conditions required to ensure dynamic similarity between the model and prototype. Determine the fraction of the prototype speed in air at which the model test should be made in water to ensure dynamically similar conditions Measurements made at various speeds show that the dimensionless force ratio becomes constant...
A model of a submarine, 1:15 scale is to be tested at 180ft/s in
a wind tunnel with standard sea-level air, while the prototype will
be operated in sea water.
A model of a submarine, 1:15 scale, is to be tested at 180 ft/s in a wind tunnel with standard sea-level air, while the prototype will be operated in seawater. Determine the speed of the prototype to ensure Reynolds number similarity. Hint: The Reynolds number of the model and prototype...
Ex.3 /35 A Cessna 172 has a cruise speed V-226 km/h and weight W-1,000Kg. The wing area is S-16mt with a wing span b-1lm Assuming the wing rectangular, what is the Reynolds number at an altitude z-1,000m. A model of this airplane, scaled by a factor of 2, is tested in a wind tunnel at sea level. What should be the velocity in the wind tunnel to have dynamics similarity (neglect Mach number effects). What will be the lift measured...
[10 points] A model of a submarine, 1:15 scale, is to be tested at 180 ft/s in a wind tunnel with standard sea-level air, while the prototype will be operated in seawater. Determine the speed of the prototype to ensure dynamic similarity 4. Properties of air: p 2.38x103 slugs/ft3, 3.74 x 107 Ib-s/ ft2 Properties of seawater: 1.99 slugs/ft3JL-2.51 x 10-5 lbs/ ft.
A model test is to be conducted in a water tunnel using a 1: 20 model of a submarine, which is to travel at a speed of 12 km/h deep under sea surface. The water temperature in the tunnel is maintained, so that is kinematic viscosity is half that of sea water. At what speed is the model test to be conducted to produce useful data for the prototype?
A model test is to be conducted in a water tunnel using a 1: 20 model of a submarine, which is to travel at a speed of 12 km/h deep under sea surface. The water temperature in the tunnel is maintained, so that is kinematic viscosity is half that of sea water. At what speed is the model test to be conducted to produce useful data for the prototype?
Most questions answered within 3 hours.
-
Python Program: Design the logic for and implement a program
that merges the two files into...
asked 8 minutes ago -
Human relations refer to the way a company arranges people,
jobs, and communications so that work...
asked 10 minutes ago -
The specific radiocarbon activity of a sample of wood is 6.25
gms dpm/gm of carbon. The...
asked 13 minutes ago -
An aqueous magnesium chloride solution is made by dissolving
6.96 moles of MgCl2 in sufficient water...
asked 15 minutes ago -
Ken believes the average age of men who come to get a haircut at
his barber...
asked 37 minutes ago -
(Ratio Analysis): Last year Co. XYZ had sales of $ 400,000, with
“cost of goods sold”...
asked 46 minutes ago -
can someone please write the balanced chemical
equation for the synthesis of Bromoacetanilide
from;
aniline +...
asked 42 minutes ago -
1. If a corporation purchases land and building and subsequently
tears down the building and uses...
asked 53 minutes ago -
Consider a 23-year bond with 7 percent annual coupon payments.
The market rate (YTM) is 6.4...
asked 56 minutes ago -
a tuba creates a 4th harmonic of frequency 116.5 Hz. what is the
frequency of the...
asked 1 hour ago -
A coconut mass 2kg falls from a 30m tall tree. The coconut falls
and comes to...
asked 1 hour ago -
Group Policies
Research GROUP POLICY OBJECTS (GPO'S)
You can start in the Windows Server 2012 eBook...
asked 1 hour ago