A certain part of an aircraft engine has a volume of 1.6 ft^3 A. Find the...
A certain part of an aircraft engine has a volume of 1.6 ft^3
A. Find the weight of the piece, when it is made of brass.
B. If the same piece is made of aluminum, what is its weight ?
C. Determine how much weight is saved by using aluminum instead of brass
. (please show the step used to get these answers)
Homework Answers
a)density if brass = 8.5 gm/cc
so the volume will have a weight of 8.5 *1.6*30.48^3 / 1000 = 385.11 kg.
b) density of aluminium = 2.7 gm /cc
so the volume will have a weight of 2.7 *1.6*30.48^3 / 1000 = 122.33 kg.
c) 262.78 kg of wt is saved by using aluminum instead of brass
Add Answer to:
A certain part of an aircraft engine has a volume of 1.6
ft^3
A. Find the...
A certain part of an aircraft engine has a volume of 2.6 ft3. (a) Find the...
A certain part of an aircraft engine has a volume of 2.6 ft3. (a) Find the weight of the piece when it is made of brass. (b) If the same piece is made of aluminum, what is its weight? Determine how much weight is saved by using aluminum instead of brass. (please explain)
A certain part of an aircraft engine has a volume of 2.0 ft3. (a) Find the...
A certain part of an aircraft engine has a volume of 2.0 ft3. (a) Find the weight of the piece when it is made of copper. (b) If the same piece is made of aluminum, what is its weight? Determine how much weight is saved by using aluminum instead of copper.
A certain part of an aircraft engine has a volume of 2.6 ft3. The weight of...
A certain part of an aircraft engine has a volume of 2.6 ft3. The weight of the piece when it is made of copper is 1445.88 lb. If the same piece is made of aluminum, what is its weight? ____lb
8. You decided to go camping and wanted to find out how much liquid propane is...
8. You decided to go camping and wanted to find out how much liquid propane is left in a used cylinder. The weight of this cylinder when it is full and empty is 80 pounds and 20 pounds respectively. Currently it weighs 50 lb. If the densities of liquid and vapor propane at 70 degree F are: 30.19 lb/ft^3 and 1.15 lb/ft^3 respectively. Determine: (a) Volumetric percentage of the propane liquid phase left the cylinder (b) Mass fraction of liquid...
3. As part of a packaging process, cans roll along a ramp from one location to...
3. As part of a packaging process, cans roll along a ramp from one location to another. In one section, the cans 1) go through a curve and make a 90 degree turn and then 2) go down a ramp from one level to another. The cans have a diameter of 4 inches, a height of 4", and a weight of 1.61 lbs. The upper level is 4 feet above the lower level. The cans roll onto into the curve...
This is cost accounting question. Please help me in part 3 (part 3 has 3 answers)...
This is cost accounting question. Please help me in part 3 (part
3 has 3 answers) and 4. Show calculations please so I can see where
I am wrong. Please do it correctly.
This initial per-day charge was quoted to patients entering the orthopedic center during the first two months with assurances that if the actual operating costs of the new center justified it, the charge could be less. In no case would the charges be more. A temporary policy...
P8.023 GO Multipart Part 1 A channel shape is used to support the loads shown on the beam. The dimensions of the...
P8.023 GO Multipart Part 1 A channel shape is used to support the loads shown on the beam. The dimensions of the shape are also shown. Assume La-3 ft, Lac-9 ft, P-2000 lb, w 850 Ib/ft, b-14 in., d-10 in., t-0.625 in. Consider the entire 12-ft length of the beam and determine (a) the maximum tension bending stress at any location along the beam, and (b) the maximum compression bending stress at any location along the beam. 14 Break the...
What is the position of the center of mass of the part? 6 point (s) m...
What is the position of the center of mass of the part? 6 point (s) m 2D Moment of Inertia You are designing a part for a piece of machinery. The part consists of a piece of sheet metal cut as shown below. The shape of the upper edge of the part is given by y1(x), and the shape of the lower edge of the part is given by y2(x) You are correct. Your receipt no. is 158-2419 Now you...
Slow Help T ED.21* 9.4. ADS 115 a aa a ab ap & 2. 15 11.16...
Slow Help T ED.21* 9.4. ADS 115 a aa a ab ap & 2. 15 11.16 LIVE! !! 3. When determining the empirical formula experimentally, you will not know the number of moles directly since we do not have instrumentation that can measure the quantity of moles. Instead the mass can be used. In an experiment it is found that an aluminum oxide sample contains 1.35 g of aluminum and 1.20 g of oxygen. a. How many moles of aluminum...
based on data please help fill out chart and questions 1,2,3 Part II: Neutralization of the...
based on data please help fill out chart and questions
1,2,3
Part II: Neutralization of the Tablet 1. Obtain one of the commercial antacid tablets that your Lab Instructor has assigned you. 2. Weigh and record the weight of the tablet. 3. Crush the tablet using mortar and pestle. 4. Transfer as much of the crushed tablet as you can onto a weigh boat. 5. Weigh the tablet and weigh boat, and record this value. 6. Pour the entire contents...
8. You decided to go camping and wanted to find out how much liquid propane is left in a used cylinder. The weight of this cylinder when it is full and empty is 80 pounds and 20 pounds respectively. Currently it weighs 50 lb. If the densities of liquid and vapor propane at 70 degree F are: 30.19 lb/ft^3 and 1.15 lb/ft^3 respectively. Determine: (a) Volumetric percentage of the propane liquid phase left the cylinder (b) Mass fraction of liquid...
3. As part of a packaging process, cans roll along a ramp from one location to another. In one section, the cans 1) go through a curve and make a 90 degree turn and then 2) go down a ramp from one level to another. The cans have a diameter of 4 inches, a height of 4", and a weight of 1.61 lbs. The upper level is 4 feet above the lower level. The cans roll onto into the curve...
This is cost accounting question. Please help me in part 3 (part
3 has 3 answers) and 4. Show calculations please so I can see where
I am wrong. Please do it correctly.
This initial per-day charge was quoted to patients entering the orthopedic center during the first two months with assurances that if the actual operating costs of the new center justified it, the charge could be less. In no case would the charges be more. A temporary policy...
P8.023 GO Multipart Part 1 A channel shape is used to support the loads shown on the beam. The dimensions of the shape are also shown. Assume La-3 ft, Lac-9 ft, P-2000 lb, w 850 Ib/ft, b-14 in., d-10 in., t-0.625 in. Consider the entire 12-ft length of the beam and determine (a) the maximum tension bending stress at any location along the beam, and (b) the maximum compression bending stress at any location along the beam. 14 Break the...
What is the position of the center of mass of the part? 6 point (s) m 2D Moment of Inertia You are designing a part for a piece of machinery. The part consists of a piece of sheet metal cut as shown below. The shape of the upper edge of the part is given by y1(x), and the shape of the lower edge of the part is given by y2(x) You are correct. Your receipt no. is 158-2419 Now you...
Slow Help T ED.21* 9.4. ADS 115 a aa a ab ap & 2. 15 11.16 LIVE! !! 3. When determining the empirical formula experimentally, you will not know the number of moles directly since we do not have instrumentation that can measure the quantity of moles. Instead the mass can be used. In an experiment it is found that an aluminum oxide sample contains 1.35 g of aluminum and 1.20 g of oxygen. a. How many moles of aluminum...
based on data please help fill out chart and questions
1,2,3
Part II: Neutralization of the Tablet 1. Obtain one of the commercial antacid tablets that your Lab Instructor has assigned you. 2. Weigh and record the weight of the tablet. 3. Crush the tablet using mortar and pestle. 4. Transfer as much of the crushed tablet as you can onto a weigh boat. 5. Weigh the tablet and weigh boat, and record this value. 6. Pour the entire contents...
Most questions answered within 3 hours.
-
. For this set of questions, determine what
proportion of a normal distribution is located betweeneach...
asked 5 minutes ago -
A college student is employed as a door-to-door newspaper
salesman. Historical data suggests that the student...
asked 59 minutes ago -
MATLAB HW 11 problem using Switch Case and Input commands
Write a script file that calculates...
asked 44 minutes ago -
Considering gravitational time dilation, calculate the time that
passes in Earth’s surface while 1 hour passes...
asked 1 hour ago -
Minitab Problem: Take the Lake Hume June rainfall data and find
use the processes outlined in...
asked 2 hours ago -
X Company is trying to decide whether to continue using old
equipment to make Product A...
asked 2 hours ago -
IN PYTHON ONLY !! Program 2: Re-work
program #5 (WeeklyHours) from the previous assignment such that...
asked 2 hours ago -
The average length of time between arrivals at a turnpike
toll-booth is 26 seconds. What is...
asked 4 hours ago -
(a) A piston at 6.1 atm contains a gas that occupies a volume of
3.5 L....
asked 5 hours ago -
Please answer true or false. Words
cannot be changed or added in to make it true...
asked 5 hours ago -
An empty test tube weighs 15.923 grams. Then,
MgCl2•6H2O is added into the test tube. After...
asked 5 hours ago -
Assume memory access is 10 units of time and disk access is
10000 units of time....
asked 6 hours ago