Which of the following forces should be included on the force diagram for this block? Draw your force diagram on the worksheet paper and then use it to check the appropriate boxes below.
Homework Answers
mention in comment if you have any doubt
Add Answer to:
Which of the following forces should be included on the force
diagram for this block? Draw...
The figure below shows a block with mass m = 5.3 kg pulled up a ramp...
The figure below shows a block with mass m = 5.3 kg pulled up a ramp inclined at an angle of 6 = 28° with a force of magnitude F = 33 N parallel to the ramp. m (a) If there is no friction between the block and the ramp, what is the magnitude of the block's acceleration (in m/s2)? 1.485 Draw a free-body diagram. What forces act on the block? Let the x-axis be parallel to the incline. What...
Block 1 (20 kg) is pulled by a rope from left to right up a ramp...
Block 1 (20 kg) is pulled by a rope from left to right up a ramp which is inclined 30 degrees from the horizontal. The rope pulls on block 1 with a force of 220 N parallel to the surface of the inclined plane. The coefficient of kinetic friction between the block and the surface equals 0.1. On a sheet of paper, draw the free body diagram for block 1 using the two-subscript notation from class. Assume that the x-axis...
Block 1 (15 kg) is pulled by a rope from left to right up a ramp...
Block 1 (15 kg) is pulled by a rope from left to right up a ramp which is inclined 45 degrees from the horizontal. The rope pulls on block 1 with a force of 255 N parallel to the surface of the inclined plane. The coefficient of kinetic friction between the block and the surface equals 0.3. On a sheet of paper, draw the free body diagram for block 1 using the two-subscript notation from class. Assume that the x-axis...
330 As shown in the figure, a 25 kg block is being pulled by a force...
330 As shown in the figure, a 25 kg block is being pulled by a force Fup along a rough incline. The coefficient of kinetic friction between the block and the incline is uk = 0.30. Keep 2 decimal places in all answers. Step 1: Start by drawing a free body diagram of the block, including all the forces exerted on the block. Label the normal force as FN, label the weight as weight. Since the type of the frictional...
Block 1 (m1 = 6 kg) and block 2 (m2 = 7 kg) are adjacent to...
Block 1 (m1 = 6 kg) and block 2 (m2 = 7 kg) are adjacent to each other on the surface of a table. Block 2 is to the LEFT of block 1. A rope pulls on block 2 up and to the right with a vertical tension of 40 N upward, and both blocks move right with an acceleration of magnitude 6 m/s2. The coefficient of kinetic friction between the blocks and the surface equals 0.4. On a sheet...
Please help. Block 1 (m1 = 5kg) and block 2 (m2 = 6 kg) are adjacent....
Please help. Block 1 (m1 = 5kg) and block 2 (m2 = 6 kg) are
adjacent.
Block 1 (m1 5 kg) and block 2 (m2 6 kg) are adjacent to each other on the surface of a table. Block 2 is to the LEFT of block 1. A rope pulls on block 2 up and to the right with a vertical tension of 30 N upward, and both blocks move right with an acceleration of magnitude 3 m/s2. The coefficient...
Rachel is pushing a box across the floor while Jon, at the same time, is hoping...
Rachel is pushing a box across the floor while Jon, at the same time, is hoping to stop the box by pushing in the opposite direction. There is friction between the box and floor but you may ignore the effect of air resistance. Draw the force diagram for the box's motion and then choose the appropriate forces from the following list that should be included on the force diagram. Assume that the box is moving to the right during the...
All work for these problems should be in your test for the in-class test, and on...
All work for these problems should be in your test for the in-class test, and on your own paper for the retest. Write down relevant equations, draw diagrams and show all of your work and label the different parts for full credit (20 points) A 1.5 kg block of wood is launched up a wooden ramp that has a 40-degree incline. The initial speed of the block is 12 m/s. The coefficient of static friction is 0.4 and the coefficient...
A small block (m1 = 4.0 kg) rests on an inclined plane (m2 = 12.0 kg,...
A small block (m1 = 4.0 kg) rests on an inclined plane (m2 = 12.0 kg, ? = 53.13?). The coeffi- cients of static and kinetic friction between the surfaces of the block and the ramp are, respectively, ?s = 0.333 and ?k = 0.200. A force F?P pushes horizontally on the inclined plane to the right, causing the system to accelerate. If the force F?P is too large, the small block will slide up the ramp, whereas, if the...
1. A block with weight W = 30 N is on a flat horizontal surface. You...
1. A block with weight W = 30 N is on a flat horizontal surface. You pull to the right with a force F = 16 N. There is gravity present and the coefficient of friction is static = 0.4 and kinetic - 0.25. You are also pulling straight up with an applied force of 12 N. Now what are: The normal force N-_ the frictional force f- the net force on the block Foot and acceleration a = 2....
The figure below shows a block with mass m = 5.3 kg pulled up a ramp inclined at an angle of 6 = 28° with a force of magnitude F = 33 N parallel to the ramp. m (a) If there is no friction between the block and the ramp, what is the magnitude of the block's acceleration (in m/s2)? 1.485 Draw a free-body diagram. What forces act on the block? Let the x-axis be parallel to the incline. What...
330 As shown in the figure, a 25 kg block is being pulled by a force Fup along a rough incline. The coefficient of kinetic friction between the block and the incline is uk = 0.30. Keep 2 decimal places in all answers. Step 1: Start by drawing a free body diagram of the block, including all the forces exerted on the block. Label the normal force as FN, label the weight as weight. Since the type of the frictional...
Please help. Block 1 (m1 = 5kg) and block 2 (m2 = 6 kg) are
adjacent.
Block 1 (m1 5 kg) and block 2 (m2 6 kg) are adjacent to each other on the surface of a table. Block 2 is to the LEFT of block 1. A rope pulls on block 2 up and to the right with a vertical tension of 30 N upward, and both blocks move right with an acceleration of magnitude 3 m/s2. The coefficient...
All work for these problems should be in your test for the in-class test, and on your own paper for the retest. Write down relevant equations, draw diagrams and show all of your work and label the different parts for full credit (20 points) A 1.5 kg block of wood is launched up a wooden ramp that has a 40-degree incline. The initial speed of the block is 12 m/s. The coefficient of static friction is 0.4 and the coefficient...
1. A block with weight W = 30 N is on a flat horizontal surface. You pull to the right with a force F = 16 N. There is gravity present and the coefficient of friction is static = 0.4 and kinetic - 0.25. You are also pulling straight up with an applied force of 12 N. Now what are: The normal force N-_ the frictional force f- the net force on the block Foot and acceleration a = 2....
Most questions answered within 3 hours.
-
Write a chemical equation for these reactions. (Use
the lowest possible whole number coefficients.) Include
states-of-matter...
asked 1 hour ago -
For each of the Z-scores below, determine two probabilities
(show four three decimal places): (1) the...
asked 1 hour ago -
Oxidative phosphorylation is achieved through chemiosmotic
coupling, which turns chemical energy into osmotic potential energy
that...
asked 4 hours ago -
Hollywood Shoes would like to maintain their cash account at a
minimum level of $64,000, but...
asked 4 hours ago -
Proteins CtrA-P, DnaA, and GcrA behave similarly to what
molecule in the Eukaryotic Cell Cycle?
asked 4 hours ago -
TRUE OR FALSE
In case of a competitive tender procedure, in the request for
quotation, the...
asked 4 hours ago -
I am a little behind please provide some explanation, will
provide thumbs up.
This question considers...
asked 4 hours ago -
Let say the utility function as U(X,Y) = lnX + Y. Show that the
marginal rate...
asked 4 hours ago -
A current of I=8.0A is flowing in a typical extension cord of
length L=3.00m. The cord...
asked 4 hours ago -
1. When balancing the equation H2SO4 (aq) + NaOH (aq) →
Na2SO4(aq) + H2O(aq), would you...
asked 5 hours ago -
Provide a definition of “classification hierarchy” and
illustrate your definition with an example of how and...
asked 5 hours ago -
1. Describe the four main green solvents. Provide one example of
the use of each solvent....
asked 5 hours ago