Determine the types of aciliary views needed to draw for the following objects A Depth auciliary...

Question

Question

Determine the types of aciliary views needed to draw for the following objects A Depth auciliary view 8 Width lary view C Hei

Answer 1

Answer #1

C. Height auxiliary view because true height can be shown from top or bottom view.

A. Depth auxiliary view because true depth can be shown from front view

Please rate my answer. Thank You.

Answer 2

Similar Homework Help Questions

Sketch, draw with SolidWorks, then create the necessary views, including a section view, of the objects...

Sketch, draw with SolidWorks, then create the necessary views, including a section view, of the objects shown and create a 3-D model. 360145 - 06.0 90 & 180° 23.05 2X 6.12 WIDE - 24.04- METRIC Figure 8.67 Round adaptor
ORTHOGRAPHIC AND SECTIONAL VIEWS 1. Draw complete orthographic drawing of the objects shown in Figure 1...

ORTHOGRAPHIC AND SECTIONAL VIEWS 1. Draw complete orthographic drawing of the objects shown in Figure 1 with full sectional front view. Also show the effect of intersection(s). RIS 12 R24 ar -1/5 ben os R20 R.20 Je (d) Figure 1 30 20 Dia 8 22 616 RIS or 40 R24 RIS 74 22 42 a) (b) 30 20 Dia 8 22 616 RIS or 40 R24 RIS 74 22 42 a) (b)
lle PPont View of object, given the lop and Rignt views as 2. Fill in the table below with the appropriate relative coordinates needed to draw this object in AutoCAD and then draw the object in A...

lle PPont View of object, given the lop and Rignt views as 2. Fill in the table below with the appropriate relative coordinates needed to draw this object in AutoCAD and then draw the object in AutoCAD. 50 (E 90 40 G) (F) 40 (A Point A, Absolute Coordinate: (0,0) 75 50 To Point A to B B to C C to D D to E E to F F to G G to H нь! I to A Relative...

2 + DRAW ALL THE ORTHOGRAPHIC VIEWS AND DIMENSION PROPERLY. ADD ANY NOTES NEEDED 1.50 DRAW...

2 + DRAW ALL THE ORTHOGRAPHIC VIEWS AND DIMENSION PROPERLY. ADD ANY NOTES NEEDED 1.50 DRAW AT 3/4 SCALE -3.00 1.00 B B 1.00 01.00 + 1.00 POST SLOT IS 1.00 DEEP 00 4 -2.00 4.00 71.00 -1.00 - -3.00 А Draw necessary orthographic views of the given object with a scale 1:1 on A4 sheet. Problem is adapted from Rol (31) Lifting block
Complete the following section view drawings with dimensions and necessary views. Do not draw the pictorial...

Complete the following section view drawings with dimensions and necessary views. Do not draw the pictorial views. They are shown to assist you in visualization. Dimension views fully. 138- 118 Finish All Over: 1 um Material: Phosphor bronze Part Name: Valve Stem PROBLEM 12.34 Removed section (metric) 84 42- 19 - -09.6 09.6 038 07.88 2 4X R LEFT-SIDE VIEW 7.86 V 69.5 RIGHT-SIDE VIEW LØ28 15.06 - 59.2- 68.8 - -- 128- NOTE: Some hidden lines omitted for clarity....
Draw each part and then create Multiview drawings utilizing auxiliary views to be more descriptive while...

Draw each part and then create Multiview drawings utilizing auxiliary views to be more descriptive while dimensioning. Drawing Number: 12 Part Name: Cylinder Support Material: Cast Iron Units: Inches |Primary Auxiliary View 2S CYLINDER DEPTH: 3.00 2

DRAWING -1: Draw the following views to describe the object in Figure D a sectional FRONT view on...

DRAWING -1: Draw the following views to describe the object in Figure D a sectional FRONT view on A-A, - a SIDE view from B, -a TOP view DIMENSIONS ARE IN MILLIMETRES PLOT THE DRAWING ON A SCALE OF 1: M30 x2 2 x φ10 R12 R 6 25 20 638 DRAWING -1: Draw the following views to describe the object in Figure D a sectional FRONT view on A-A, - a SIDE view from B, -a TOP view DIMENSIONS...
Please draw the top,front and right view for the following isometric views. Please don't forget to...

Please draw the top,front and right view for the following isometric views. Please don't forget to use engineering paper.
Please draw 3D view in one box to show me the view three views in one...

Please draw 3D view in one box to show me the view three views in one shape for the left and the right shapes supratl Left side is different than right side the are two shapes which are needed to be drown in 3D shape and Draw section AA for left shape & BB section for right side

1. Draw complete orthographic drawing of the objects shown in Figure 1 with full sectional front...

1. Draw complete orthographic drawing of the objects shown in Figure 1 with full sectional front view. Also show the effect of intersection(s). ORTHOGRAPHIC AND SECTIONAL VIEWS 1. Draw complete orthographic drawing of the objects shown in Figure 1 with full sectional front view. Also show the effect of intersection(s). 20 Dia 46 22 616 R15 R24 30 22 RIS 42 (a) (b) -1/5- 15.15.20 24 40 20 50 Ss R20 R20 R20 R20 80 90 50 (d) Figure 1