The block in figure below has dimensions of a = 2m, b = 5m, and c...

Question

Question

The block in figure below has dimensions of a = 2m, b = 5m, and c = 1m. If force F= 10i + 5j - 10k, what is the moment of F a

Answer 1

Answer #1

Foxie Verlox_] - loi + Sj -10K Position vector XOA = (XA - x0) i + (yo-Yd)j + (ZA-Ze)k = 2 i + 5j + OK Mo=80A x نأ 2 5 10 5 -

Answer 2

Similar Homework Help Questions

2a. Block A of mass "2m" sits on top of block B of mass "m". There...

2a. Block A of mass "2m" sits on top of block B of mass "m". There is no friction between block B and the floor, but there is friction between the two blocks. Block B is pulled by a force "F" to the left. Write out the force equations on each block for the case of no slipping between the blocks. Don't solve FA - EFA- EFR = EF= 2b. The pulley (disk) shown has a mass "m" and radius...
Statics Problem Problem #5 In the Diagram below, there are 2 forces acting on the pipe....

Statics Problem Problem #5 In the Diagram below, there are 2 forces acting on the pipe. a) Moment at Point O, (10 pts) b) Moment about the line OA (Section between the origin and 1" pipe joint)(10 pts) c) Moment about the line AO (5 pts) F2 1-10i +25j + 20k) Ib 2 ft 0 1.5 ft 2ft 2 f Problem #6( The Beam in the Figure below is subjected to 3 forces. Determine by any method of choice: a)...
Using the position vector from A to C, calculate the moment about segment A B due to force F.

The general process (not referenced to Figure 1) to calculate the moment of a force about a specified axis is as follows:The magnitude of a moment about a line segment connecting points P and Q due to a force F applied at point R (with R not on the line through P and Q ) can be calculated using the scalar triple product,MPQ=uPQ · r × Fwhere r is a position vector from any point on the line through P...

Point "A" is on the part (rectangular block) shown in figure below and has a coordinate...

Point "A" is on the part (rectangular block) shown in figure below and has a coordinate of (5, 5, 0) The part goes through the following set of transformation in the order shown below: a. 90° rotation clock wise about the X axis b. Translation along the vector (1,1,1) What is the final coordinate of point A after these translations? A: (5, 5, 0)
PROBLEM 1 (35 %) The mechanical system in the figure below consists of a disk of radius r, a block of mass m, a spr...

PROBLEM 1 (35 %) The mechanical system in the figure below consists of a disk of radius r, a block of mass m, a spring of stiffness (spring constant) k, and a damper with damping ratio b. The disk has moment of inertia Jabout its center of mass (pivot point O), and the block is subjected to an external force t) as shown in the figure. The spring is unstressed when x 0= 0. Assume small 0. (a) (10 points)...
Eng 203 (mechanics) 9. For the bracket under a 90-N force shown below, complete t Torce...

Eng 203 (mechanics) 9. For the bracket under a 90-N force shown below, complete t Torce shown below. complete the following questions. (a) (10 pts) Define the rectangular coordinate system.Draw the positive and origin in the figure. (b) (10 pts) Express the position vector from point O to point A, POA (C) (20 pts) For = 15°, express the force as a vector in form Fi +F, j . Then calculate the moment of the 90-N force about point o....

1. A pipe structure in the figure below has a force exerted on it at point...

1. A pipe structure in the figure below has a force exerted on it at point C as shown. F 2888 + 384ý - 2402) N a. Determine the position vector from A to C b. Using the cross product, determine the moment of the force about point A. c. Using scalar analysis, the components of the position vector, and the components of the force vector, recalculate the moment about the x, y, and z axis 300 mm 240 mm...
Figure 1 ab. OCRO d Figure Dimensions a = 300 mm, b = 100 mm, c...

Figure 1 ab. OCRO d Figure Dimensions a = 300 mm, b = 100 mm, c = 50 mm, d = 450 mm F = 500 N Objective #1: Draw a FBD of the decomposed member(s) and determine clamping force produced by the rubber pad on the wood block at A. 8 points What is the magnitude of the clamping force NA? Enter the force magnitude with three significant figures with units as appropriate. Your answer 2 points This machine...
1. The block shown in the figure has a mass of 612 Kg. The static coefficient...

1. The block shown in the figure has a mass of 612 Kg. The static coefficient of friction between the block and the supporting surface is 0.33 while the kinetic coefficient of friction is 0.26. Ignore the size of the block. Force P is parallel to the incline while the 1000N force is vertical. a) If P = 2000 N, the shown block is (circle the correct answer) (5 points) a) in equilibrium b) moving up the incline c) is...

Please answer this ASAP!! Moment of a Force-Vector Formulation Learning Goal To use the vector cross...

Please answer this ASAP!! Moment of a Force-Vector Formulation Learning Goal To use the vector cross product to calculate the moment produced by a force or forces, about a specified point on a member The moment of a force F about the moment axis passing through O and perpendicular to the plane containing o and F can be expressed using the veotor cross product, Mo x F. n a properly constructed Cartesian coordinate system he vector cross product can be...