Question

QUESTION 3 Calculate the reactions at the supports, then illustrate the moment diagram. The moment of inertia for each segmen

Please use virtual work method (full solution please with drawing)

0 0
Add a comment Improve this question Transcribed image text
Know the answer?
Add Answer to:
Please use virtual work method (full solution please with drawing) QUESTION 3 Calculate the reactions at...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • n: Question 1 Use Moment Distribution method to determine the reactions of the continuous beam shown...

    n: Question 1 Use Moment Distribution method to determine the reactions of the continuous beam shown in Figure 1. Modulus of Elasticity, E, is constant and Moment of Inertia, l, is as shown. The reactions at B, D, E, F are rollers and at Cis a pin. Use five cycles in your solution. 2.1 . 2 kN/m SEN yer Shen 4KN A AC I 21 21 31 31 21 2m 4m 4m 8m 4m Ant 2m 2m Figures

  • 1. Determine the reactions at the supports. Assume the support at A is fixed and B...

    1. Determine the reactions at the supports. Assume the support at A is fixed and B is a roller. Take E 200 GPa. The moment of inertia for each segment is given. Use principle of virtual work to find all required displacements. 25 kN 30 kN/m ГВ IAB 360(10) mm A TBC 180(10) mm 6 m 4 m

  • QUESTION 1 [25 marks A frame loaded with a uniformly distributed load at Member AB and...

    QUESTION 1 [25 marks A frame loaded with a uniformly distributed load at Member AB and point load at Member BC and joint B. It has pinned supports A and C, while joint B is fixed connected, as can be seen in Figure 1. Take E-200 GPa. a) Using the slope-deflection method, calculate the moments and illustrate the bending moment diagram. [15 marks) b) Then calculate the shear forces and sketch the shear force diagram. [10 marks) 22 KN 10...

  • 1) Determine the reactions at the supports for the structures shown. The support at A is...

    1) Determine the reactions at the supports for the structures shown. The support at A is a Roller and the support at B is a Pin. 2.0 k/ft M 10 k- 3.0 k/ft 12 ft 25 k- 25k-Pokift 15 ft B! 1 F20ft- 2) 2 3 k/ft A beam is supported at points A, C, and E, and is loaded as shown. The support at A is fixed. The supports at C and E are rollers. Hinge-B ce Dl Hinge...

  • please disregard work For the structure shown below, using the FORCE METHOD determine the reactions at...

    please disregard work For the structure shown below, using the FORCE METHOD determine the reactions at A and at C when a distributed load w =6 kN/m is applied on the column and concentrated load P=20 kN applied on the beam as shown. (Moment of inertia for the beam is 2xl and for the column is 3xl same material. E= 200 GPa and 1 = 240x106 mm. A is a built-in support, the members are rigidly connected at B and...

  • Name 1Pag Question 1 (35 marks) Use the method of virtual work to determine the vertical displace...

    structure design Name 1Pag Question 1 (35 marks) Use the method of virtual work to determine the vertical displacement of joint C of the truss below The cross-sectional area of each member is A 300 mm2 and E- 200 GPa Note 1 GPa -1.0 x 10 kN/m 1 mm2-10 x 10-*m2 3 kN 2 m 2 m 1.5 m EA Set out wour computations as follows (a) Find the reactions at hinge support E and at roller support A b)...

  • 0 Question 3 a) Using the Force Method, determine the reactions at all supports. In addition to t...

    0 Question 3 a) Using the Force Method, determine the reactions at all supports. In addition to the applied loads, support at A rotates 0.005 radian counterclockwise Given E=200GPa and i=150 x 106 mm! 200 x 109 (20 marks) oda rotation 5 kN/m 25 kNm 10 m 6 m By Figure 3 b) If a spring is connected at point C, determine the force in this spring using the force Method By comparing to the solution in Question 3(a), what...

  • Please solve the following question using the force method. I need a full solution to check...

    Please solve the following question using the force method. I need a full solution to check my work. Thanks Will rate thumbs up. 6.2.For the following frames, i)Determine the degree of indeterminancy. ii)Calculate the support reactions. iii) Draw the moment and shear diagrams. a) EAC = 200Gpa, IAB = 250x 106 mm. IBC = 150x 106 mm" 10 KN/m 2m 70 KN 2m

  • Solve question one the drawing is right beside it and the key answer I want explaining...

    Solve question one the drawing is right beside it and the key answer I want explaining step by step for the drawing and the forces found please Problem 1: Find the support reactions and draw the moment diagram for the beam: (CLO #2) 15kN/m Find support moment: 20x3-(15x3/2)+M-Mp-7.5kN-m. Static Moment: 15x3/8-16.875kN-m Ok MB Ra Rcv 15kN Rehx3-5x2-5x4-5x6 0 RG.hz 60/3-20kN =-Rah Ro.b 3 in Problem 2 Solve the truss forces at node A using (a) The method of Sections and...

  • Hi could u be more clearly when u solve the question please and thanks for helping...

    Hi could u be more clearly when u solve the question please and thanks for helping 5:53 PM unilearn.southwales.ac.uk 3 4G 2018 2019 NG2S230_EX1Mock Paper PartA (7 marks) (25 marks) Question 2 A small footpath bridge will be built over a segment of the river Taff. The bridge will span 15 metres. When testing the bridge, two loads of 150 kN were placed on it. One at 2 metres from the left support and another 3 m from the right...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT