For motor inductance is assumed to be large.
3) A saperately excited DC motor has the following parameters: Ra = 10 Ke = 0.4...
3) A saperately excited DC motor has the following parameters: Ra = 10 Ke = 0.4 V/rpm. Wb O = 0.2 Wb The motor speed is controlled by a full-wave bridge rectifier. The firing angle is set at 45, and the average speed is 1500 rpm. The applied AC voltage to the input of the bridge rectifier is 220Vrms - 50 Hz. a) (10p) Please draw the complete circuit. (converter + motor) b) (10p) Please find the armature current. c)...
solve it now please A 220 V, 1000 rpm, separately excited dc motor is fed from a three-phase controlled three-phase ac-dc converter through 220 V (line value-rms value), 50 Hz ac-source. It is required to apply 220 V (dc-value) across the motor terminals. What is the firing angle if the motor speed is 1000 rpm and takes 10 A ripple-free current. The armature resistance is 1 ohm. The field circuit with 198 ohms is fed from a fully controlled single-phase...
A power electronic converter used to drive a separately-excited DC motor for application in Sohar, Oman as shown in Figure Q2. Let R = 0.25 , K = 0.62 V/rpm.Wb, (flux per pole) = 175 mWb. The used converter is a single-phase, controlled full-wave bridge rectifier. Assume the firing angle is 45°, and the average speed is 1300 rpm and torque constant K is 9.55 of K. Assuming the motor current is continuous; calculate the armature current drawn by the...
6. The speed of a 150 HP, 650 V, 1750 rpm, separately excited DC motor is controlled by a 3- phase full converter. The converter is operating from 3-phase, 460 V, 50 Hz supply. The rated armature current of the motor is 170 A. The motor parameters are Ra = 0.099 2, La = 0.73 mH, and K.D=0.33 V/rpm. Neglect the losses in converter system. Determine i. No-load speed at firing angles a = 0º and a = 30°. Assume...
i. The speed of a separately excited dc motor is controlled by a one-phase full-wave converter. The field circuit is also controlled by a full-wave converter, see V supply) Vs pk-150V Ra-0.310 L Rf 152O E-63V α. 1-35A Figure 3 The AC supply voltage to the armature and field converters is one-phase, 150Vpeak, 50Hz. The armature resistance Ra-0.31Ω, the field circuit resistance Rf-152Ω, and the motor voltage constant is Kv-1.3V/A. The armature current corresponding to the load demand la-35A The...
Open Book Exam A 220 V, 1000 V dc-sourc rpm, separately dc motor is fed from a dc-dc converter through 550 e with duty cycle 40 %. The motor speed is 1000 rpm when takes ripple free and armature resistance is 1 Ω. The motor constant is 6/π V/A-rad/s. The field circuit with 198 Ω is fed from a controlled single-phase rectifier and set to the maximum possible value. The ac source for field circuit is 220 V, 50 Hz....
I can not seem to get the right answers. Thank you! Given a 1/4 hp, separately excited, dc motor with the following parameters: K = 0.61, R, 15Ω, La-120mb. J = 0.005, and b = 0.0006. The armature voltage is controlled by a 120-V dc PWM source operating at 100 Hz 1. What is the armature current if the no-load speed is 1800 rpm when the armature supply is operated at a 100% duty cycle? 2. What is the no-load...
please solve this problem with detail explainations. Thanks Problem # 1 If the available power source is a three-phase, 60 Hz, ac supply and a separately excited DC motor is to be fed from this source, configure possible drive circuits for iOne-Quadrant Operation, i) Two-Quadrant Operation ) Four- Quadrant Operation Hints: (See below for the single phase diagram) For one-quadrant operation, the motor control circuit is a half-wave controlled rectifier or a se controlled converter and the driver for the...
A separately-excited dc motor with the following parameters: Ra = 0.25 ohm, La = 0.003H, and Kb = 0.35 V/rad/sec. is driving a load of 1-0.0155 ke-m2, B -0.004 Nm/rad/sec with a load torque of 120 Nm. Its armature is connected to a dc supply voltage of 450 V and is given the rated field power. Determine the armature input power of the motor and choose the right answer from the given answer options. 120.5 kW 450 kW 159.6 kW...
(i) A 220 volts, 825 rpm, 125 A separately excited DC motor has an armature resistance of 0.05 2. It is fed from a single phase fully controlled rectifier with an ac source of 225 Volts, 50Hz. Assuming continuous conduction calculate (a) Firing angle for 1/4"hrated motor torque and 750 rpm (b) Motor speed for a=160 degrees and rated torque 5 Marks (ii) Draw and explain with neat circuit diagram of a DC drive circuit, which works with positive output...