Homework Answers
Add Answer to:
Show work fora thumbs up
Answer wrong and I’ll mark wrong
5. What is the capacitance...
Will give instant thumbs up, please show some work and equations if done in excel. An...
Will give instant thumbs up, please show some work and equations
if done in excel.
An experiment was performed to compare the fracture toughness of high-purity 18 Ni maraging steel with commercial-purity steel of the same type. For m = 33 specimens, the sample average toughness was x = 64.1 for the high-purity steel, whereas for n = 38 specimens of commercial steel y = 58.6. Because the high-purity steel is more expensive, its use for a certain application can...
Please answer #9 below and show all work. Will thumbs up for a prompt response (within...
Please answer #9 below and show all
work.
Will thumbs up for a prompt response (within 1
hour), thanks!
QAR Ay-Ay E -100 Repeat the process to determine the width of the central peak for the remaining cases. sy Slit width Yminl min2 Ay=min2-min) Theoretical Ay Percent difference 0.02mm 2.20 mm 20.30 mm 25.3mm 4.98 0.04 mm 7.10mm 19.00mm 11.9mm 12.7mm 6.56 0.08 mm 19.75mm 15.80mm 6.05mm 6.33mm 4.56 0.16mm 11.05mm 14.15mm 3.100mm 3.17mm 2.2% 24.1mm 9. Use Equation (4)...
summarizr the followung info and write them in your own words and break them into different...
summarizr the followung info and write them in your own words and break them into different key points. 6.5 Metering Chamber: 6.5.1 The minimum size of the metering box is governed by the metering area required to obtain a representative test area for the specimen (see 7.2) and for maintenance of reasonable test accuracy. For example, for specimens incorporating air spaces or stud spaces, the metering area shall span an integral number of spaces (see 5.5). The depth of...
summatize the following info and break them into differeng key points. write them in yojr own...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated...
10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated sludge operation that adversely affect effluent quality with origins in the engineering, hydraulic and microbiological components of the process. The real "heart" of the activated sludge system is the development and maintenance of a mixed microbial culture (activated sludge) that treats wastewater and which can be managed. One definition of a wastewater treatment plant operator is a "bug farmer", one who controls the aeration...
Will give instant thumbs up, please show some work and equations
if done in excel.
An experiment was performed to compare the fracture toughness of high-purity 18 Ni maraging steel with commercial-purity steel of the same type. For m = 33 specimens, the sample average toughness was x = 64.1 for the high-purity steel, whereas for n = 38 specimens of commercial steel y = 58.6. Because the high-purity steel is more expensive, its use for a certain application can...
Please answer #9 below and show all
work.
Will thumbs up for a prompt response (within 1
hour), thanks!
QAR Ay-Ay E -100 Repeat the process to determine the width of the central peak for the remaining cases. sy Slit width Yminl min2 Ay=min2-min) Theoretical Ay Percent difference 0.02mm 2.20 mm 20.30 mm 25.3mm 4.98 0.04 mm 7.10mm 19.00mm 11.9mm 12.7mm 6.56 0.08 mm 19.75mm 15.80mm 6.05mm 6.33mm 4.56 0.16mm 11.05mm 14.15mm 3.100mm 3.17mm 2.2% 24.1mm 9. Use Equation (4)...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
Most questions answered within 3 hours.
-
What specific indicators can point to lack of progress for
African Americans in American society?
asked 50 minutes ago -
1-The Electrons in a beam are moving at 2.7×108 m/s in an
electric field of 15000...
asked 1 hour ago -
A gas tank is a vertical cylinder. It has a radius of 1m, a
height of...
asked 1 hour ago -
Accent Software faces the following conditions. All of these
support Accent’s use of a market-penetration pricing...
asked 2 hours ago -
A mathematically inclined friend emails you the following
instructions: "Meet me in the cafeteria the first...
asked 2 hours ago -
A monopoly sells in two countries . The demand curves in the two
countries are p1...
asked 3 hours ago -
A .15kg rubber ball is bounced off a wall. Before hitting the
wall, the ball moves...
asked 4 hours ago -
A manufacturing company preparing to build a new plant is
considering three potential locations for it....
asked 4 hours ago -
B. If compound Y has approximately the same values of solubility
in toluene as compound X,...
asked 4 hours ago -
Oscar Inc. has inventory in Japan valued at 39,051,000 Yen one
year ago. One year ago...
asked 5 hours ago -
If Canada suffered from "fundamental disequilibrium," and its
government choose not to devalue its currency, a...
asked 5 hours ago -
4. How many input & output Key Value Pairs are passed into,
and emitted out of...
asked 5 hours ago