Water at 15 degrees Celcius (surface tension is 0.0742 N/m) stands in a clean glass tube of 1.5-mm diameter at a height of 45 mm. What is the true static height?
Water at 15 degrees Celcius (surface tension is 0.0742 N/m) stands in a clean glass tube...
1.128 An open, clean glass tube is inserted vertically into a pan of water. What tube diameter is needed if the water level in the tube is to rise one tube diameter (due to surface tension)? Water surface tension is 7.34*10 N/m.
N Determine the capillary rise of water in glass tube if the surface tension of water=0.00287 N/m and diameter =80 mm (Non-anonymous question ) (3 Points)
A device for sampling water in lakes and streams consists of a 2.25 cm diameter cylindrical tube that is 3 cm in length. The disks are placed in a wan technician to insert the sampling disk into the water. The tubes are then sealed in a container and taken back to the lab where the water is removed from the tube and analyzed. The tube is made of glass and contains 200 cylindrical pores 1 mm in diameter that run...
The figure shows the effect of tube radius on the height to which capillary action can raise a fluid. In this problem, assume the contact angle for water and glass is 0 degrees. The surface tension of water is .0728N/m Calculate the height, in meters, for water in a glass tube with a diameter of 1.7cm, a rather wide tube like the one on the left. What is the radius, in meters, of the glass tube on the right if...
The velocity distribution for water (15 degrees Celcius) near a wall is given by u=a(y/b)^n, where y is the distance from wall in mm and u is the velocity in m/s. The parameters, a = 22.0, b = 2.3, and n = 1/6. Determine shear stress in the water at 0.13 mm from the wall.
4. 5 points A device for sampling water in lakes and streams consists of a 2.25 cm diameter cylindrical tube that is 3 cm in length. The disks are placed in a wand that allows the technician to insert the sampling disk into the water. The tubes are then sealed in a container and taken back to the lab where the water is removed from the tube and analyzed. The tube is made of glass and contains 200 cylindrical pores...
What is the capillary rise of ethanol in a glass tube with a 0.1 mm radius if the surface tension of ethanol is 0.032Jm2 and the density of ethanol is 0.71gcm3? Assume that the contact angle of ethanol in a glass tube is 0 degrees. Your answer should have two significant figures.
Q3 [30 Marks] Water (p=1000 kg/m) is flowing through a tube with the constant surface area as shown in the Figure Q3. 150 kPa 400 kPa 2 20 m 45° 1 Figure Q3 i. Calculate the diameter, if the friction factor of the pipe, the allowed velocity and the length of transport of the water are 0.025, 1.5 m/s and 200 m respectively. [15 Marks] What will happen for the system, if the friction factor of the pipe increases to...
3. A papercip made of steel wire (psteel-7500 KE/m3) floats in water supported by surface tension (o-0.073 N/m). This paperclip has length =50 mm, cross-section diameter 1.5 mm and perimeter 103 mm. If the manufacture products the same paperclip with silver (P silver 10490 Km), will it be able to float in water with the same surface tension? Please show the calculation to support your answer. (g-9.81m/s2)
A glass tube of inside diameter 1.0 mm is dipped vertically into a container of mercury, with its lower end 1 cm below the mercury surface. a) What must be the gauge pressure of the air in the tube to blow a hemispherical bubble at its lower end? (Answer: 1400 Pa) b) To what height will mercury rise in the tube if the air pressure in the tube is 3000 Pa below atmospheric? The contact angle is 140 degrees and...