A piston having a
cross-sectional area of 0.06 m2 is located in a cylinder containing
water as shown in the figure below. An open U-tube manometer is
connected to the cylinder as shown. For h1 = 300 mm and h = 500 mm,
what is the value of the applied force, P, acting on the piston?
The weight of the piston is negligible.
Homework Answers
Add Answer to:
A piston having a
cross-sectional area of 0.06 m2 is located in a cylinder containing
water...
A piston/cylinder with a cross- sectional area of .01 m^2 has a piston mass of 100...
A piston/cylinder with a cross- sectional area of .01 m^2 has a piston mass of 100 kg resting on stops. With an outside atmospheric pressure of 120 kPa , what should the water pressure be to lift the piston?
A container of water has a cross-sectional area of A = 0.1 m^2. A piston sits...
A container of water has a cross-sectional area of A = 0.1 m^2. A piston sits on top of the water (see the following figure). There is a spout located 0.15 m from the bottom of the tank, open to the atmosphere, and a stream of water exits the spout. The cross sectional area of the spout is A_s = 7.0 times 10^-4 m^2. (a) What is the velocity of the water as it leaves the spout? (b) If the...
The construction of a water pistol is shown in the figure below. The cylinder with cross-sectional...
The construction of a water pistol is shown in the figure below. The cylinder with cross-sectional area A1 is filled with water and when the piston is pushed (by pulling the trigger), water is forced out the tube with cross- sectional area A2. The radius of the cylinder and tube are, respectively, 1.50 cm and 1.30 mm, and the center of the tube is a height - 3,00 en above the center of the cylinder. (Assume atmospheric pressure is 1.013...
The construction of a water pistol is shown in the figure below. The cylinder with cross-sectional...
The construction of a water pistol is shown in the figure below. The cylinder with cross-sectional area A, is filled with water and when the piston is pushed (by pulling the trigger), water is forced out the tube with cross-sectional area A. The radius of the cylinder and tube are, respectively, 1.50 cm and 1.40 mm, and the center of the tube is a height h = 3.00 cm above the center of the cylinder. (Assume atmospheric pressure is 1.013...
The construction of a water pistol is shown in the figure below. The cylinder with cross-sectional...
The construction of a water pistol is shown in the figure below. The cylinder with cross-sectional area A1 is filled with water and when the piston is pushed (by pulling the trigger), water is forced out the tube with cross- sectional area A2. The radius of the cylinder and tube are, respectively, 1.10 cm and 1.30 mm, and the center of the tube is a height -3.00 cm above the center of the cylinder. (Assume atmospheric pressure is 1.013 x...
The construction of a water pistol is shown in the figure below. The cylinder with cross-sectional...
The construction of a water pistol is shown in the figure below. The cylinder with cross-sectional area A, is filled with water and when the piston is pushed (by pulling the trigger), water is forced out the tube with cross-sectional area Ag. The radius of the cylinder and tube are, respectively, 1.30 cm and 1.50 mm, and the center of the tube is a height h = 3.00 cm above the center of the cylinder. (Assume atmospheric pressure is 1.013...
A spring loaded piston-cylinder device with a cross sectional area of 0.2 m2 contains 0.6 kg...
A spring loaded piston-cylinder device with a cross sectional area of 0.2 m2 contains 0.6 kg of air, as shown in the figure. The air initially at 100 kPa and 20°C, is heated to 450 kPa at which the piston begins to move. The process continues until the final volume is 12 times the initial volume. Calculate (a) the final temperature in kb) the work done in kJ. (the total heat transfer in this process Use the following properties for...
The construction of a water pistol is shown in the figure below. The cylinder with cross-sectional...
The construction of a water pistol is shown in the figure below. The cylinder with cross-sectional area A, is filled with water and when the piston is pushed (by pulling the trigger), water is forced out the tube with cross-sectional area A. The radius of the cylinder and tube are, respectively, 1.40 cm and 1.50 mm, and the center of the tube is a height h = 3.00 cm above the center of the cylinder. (Assume atmospheric pressure is 1.013...
A U-tube of uniform cross-sectional area and open to the atmosphere is partially filled with mercury....
A U-tube of uniform cross-sectional area and open to the atmosphere is partially filled with mercury. Water is then poured into both arms. If the equilibrium configuration of the tube is shown in the figure below, with h2 = 1.409 cm, determine the value of h1. The density of mercury is 13,600 kg/m^3.
A piston/cylinder arrangement with an cross sectional area of 1 mạ contains carbon dioxide at 200...
A piston/cylinder arrangement with an cross sectional area of 1 mạ contains carbon dioxide at 200 kPa and 290 K. The cylinder has a thick piston that initially held by a pin as shown in Figure 1. The metal piston has a density of 8000 kg/mº, standard acceleration of gravity, &c is 9.81 m/s and the atmospheric pressure is 101 kPa. The pin is now removed, allowing the piston to move and after a while the gas returns to 290...
A container of water has a cross-sectional area of A = 0.1 m^2. A piston sits on top of the water (see the following figure). There is a spout located 0.15 m from the bottom of the tank, open to the atmosphere, and a stream of water exits the spout. The cross sectional area of the spout is A_s = 7.0 times 10^-4 m^2. (a) What is the velocity of the water as it leaves the spout? (b) If the...
The construction of a water pistol is shown in the figure below. The cylinder with cross-sectional area A1 is filled with water and when the piston is pushed (by pulling the trigger), water is forced out the tube with cross- sectional area A2. The radius of the cylinder and tube are, respectively, 1.50 cm and 1.30 mm, and the center of the tube is a height - 3,00 en above the center of the cylinder. (Assume atmospheric pressure is 1.013...
The construction of a water pistol is shown in the figure below. The cylinder with cross-sectional area A, is filled with water and when the piston is pushed (by pulling the trigger), water is forced out the tube with cross-sectional area A. The radius of the cylinder and tube are, respectively, 1.50 cm and 1.40 mm, and the center of the tube is a height h = 3.00 cm above the center of the cylinder. (Assume atmospheric pressure is 1.013...
The construction of a water pistol is shown in the figure below. The cylinder with cross-sectional area A1 is filled with water and when the piston is pushed (by pulling the trigger), water is forced out the tube with cross- sectional area A2. The radius of the cylinder and tube are, respectively, 1.10 cm and 1.30 mm, and the center of the tube is a height -3.00 cm above the center of the cylinder. (Assume atmospheric pressure is 1.013 x...
The construction of a water pistol is shown in the figure below. The cylinder with cross-sectional area A, is filled with water and when the piston is pushed (by pulling the trigger), water is forced out the tube with cross-sectional area Ag. The radius of the cylinder and tube are, respectively, 1.30 cm and 1.50 mm, and the center of the tube is a height h = 3.00 cm above the center of the cylinder. (Assume atmospheric pressure is 1.013...
A spring loaded piston-cylinder device with a cross sectional area of 0.2 m2 contains 0.6 kg of air, as shown in the figure. The air initially at 100 kPa and 20°C, is heated to 450 kPa at which the piston begins to move. The process continues until the final volume is 12 times the initial volume. Calculate (a) the final temperature in kb) the work done in kJ. (the total heat transfer in this process Use the following properties for...
The construction of a water pistol is shown in the figure below. The cylinder with cross-sectional area A, is filled with water and when the piston is pushed (by pulling the trigger), water is forced out the tube with cross-sectional area A. The radius of the cylinder and tube are, respectively, 1.40 cm and 1.50 mm, and the center of the tube is a height h = 3.00 cm above the center of the cylinder. (Assume atmospheric pressure is 1.013...
A piston/cylinder arrangement with an cross sectional area of 1 mạ contains carbon dioxide at 200 kPa and 290 K. The cylinder has a thick piston that initially held by a pin as shown in Figure 1. The metal piston has a density of 8000 kg/mº, standard acceleration of gravity, &c is 9.81 m/s and the atmospheric pressure is 101 kPa. The pin is now removed, allowing the piston to move and after a while the gas returns to 290...
Most questions answered within 3 hours.
-
Work of 1950 J is done by stirring a perfectly insulated beaker
containing 75 g of...
asked 3 minutes ago -
The neighborhood kids set up an outdoor lemonade stand in
Maryland in June. They find that...
asked 5 minutes ago -
9. A company has a beginning inventory of 4,000 units. The
company estimates it will sell...
asked 18 minutes ago -
A patient goes to the doctor's office with symptoms of a urinary
tract infection and provides...
asked 20 minutes ago -
When responding to the essay questions, be sure to cite any
material you obtained from a...
asked 20 minutes ago -
The energy of an electron in a 2.25-eV-deep potential well is
1.50 eV.At what distance into...
asked 22 minutes ago -
Q1:Which three evolutionary innovations are present in land
plants (but not all land plants) that allowed...
asked 25 minutes ago -
Lymphosarcoma is
extremely rare. Risk factors for the disease are largely unknown.
What kind of study...
asked 27 minutes ago -
The solubility of benzoic acid in water is:
0.29g/100mL at 20°C
6.8g/100mL at 100°C
a) What...
asked 29 minutes ago -
Which food law was passed in 1996 and changed how pesticide
residues on food were regulated...
asked 47 minutes ago -
companies either hire outside programmers to
write_____ software or use their own internal developers.
asked 46 minutes ago -
A magnetic dipole m(t) = m_0*cos(ωt) can be
described as current density j(r,t) = −cm(t) ×...
asked 46 minutes ago