The machine part ABC is supported by a frictionless hinge at B and a 10° wedge at C. The coefficient of static friction is 0.20 at both surfaces of the wedge. Given F = 520 N:
A. Determine the force P required to move the wedge to the right.
B. Determine the components of the corresponding reaction at B.
The machine part ABC is supported by a frictionless hinge at B and a 10° wedge...
The machine part ABC is supported by a frictionless hinge at B and a 20° wedge at C. Knowing that the static coefficient of friction at both surfaces of the wedge is 0.3. Determine: (a) the force P required to move the wedge. (b) The components of the corresponding reaction at B (c). Draw the normal, shear and moment diagrams [40 pts 5. 1800N A 350mm 10000 N/m 400mm 600mm The machine part ABC is supported by a frictionless hinge...
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The machine part ABC is supported by a frictionless hinge at Band a 10° wedge at C. The coefficient of static friction is 0.20 at both surfaces of the wedge. The force P is applied on the wedge to push it to the left. Given: F= 660 N. 200 mm 250 mm 10° Determine the force P required...
A bent rod is supported by smooth journal bearings at A and B. Assume the rod is properly aligned. Find the reactions at all the supports, where F 600N 100N 30 Determine the intenal force, shear, and the moments at points B and C of figure 2. 4kN/m 3m 45° 1m 2m 2m Rajah 2IFigure 2 The compound beam shown in Figure 3 is pin connected at B. Determine the components of reaction at its support. Neglect its weight and...
REVIEW (Figure 1) Part A Determine the minimum applied force P required to move wedge A to the right. The spring is compressed a distance of 180 mm. Neglect the weight of A and B. The coefficient of static friction for all contacting surfaces is His = 0.35. Neglect friction at the rollers. Express your answer to three significant figures and include the appropriate units. Figure ? НА 1 of 1 P= Value Units k - 15 kN/m Submit Request...
cam ABC is supported by a post at B. The coefficient of static friction between the post and the Beall at is g = 0.28. The coefficient of static friction between the post and the ground at Dis Ho = 0.21. The coefficient of kinetic friction between the post and the beam at Bis Ug = 0.20. The coefficient of kinetic riction between the post and the ground at Dis Ho - 0.17 a) Draw a free body diagram of...
Wedge B is used to lift crate A. Crate A has a mass of 200 kg, and the mass of wedge B is negligible. The coefficient of static friction between all contact surfaces is us 0.30. Determine the force P required to begin moving the crate upward. (Ans. P 1,980 N) 3. 15°
The beam ABC is supported at A with a guided support (fixed with roller) and hinge at B has rectangular cross section and supports concentrated loads P both ends A and C as shown in the figure. The span length from A to B is L, and the length of the overhang is 1/2. Point D is located midway between the supports at a distance d from the top face of the beam Knowing that the maximum tensile stress (principal...
The beam ABC is supported at A with a guided support (fixed with roller) and hinge at B has rectangular cross section and supports concentrated loads P both ends A and C as shown in the figure. The span length from A to Bis L, and the length of the overhang is 1/2. Point D is located midway between the supports at a distance d from the top face of the beam Knowing that the maximum tensile stress (principal stress)...
2. See the question below. 8.59 A 10 wedge is to be forced under end B of the 5-kg rod AB Knowing that the coefficient of static friction is 0.40 between the wedge and the rod and 0.20 between the wedge and the floor. determine the smallest force P required to raise end B of the rod. 0.3 m
If the applied force P = 250 N, determine (a) the required minimum compression in the spring so that the wedge will not move to the right. Neglect the weight of A and B. The coefficient of static friction for all contacting surfaces (i.e. between B & A, and A & C) is ? = 0.35. Neglect friction at the rollers. (b) Draw the free body diagram of object A. (Final Answer = 0.0183 m)