Question

2. 120 ft Pump Fig.2 Water at 20 °C is to be pumped through 2000 ft of pipe from reservoir 1 to 2 at a rate of 3 ft/sec as shown in Fig.2. If the pipe is cast iron of diameter 6 in and the pump is 75 % Efficient, what horsepow pump is needed?
0 0
Add a comment Improve this question Transcribed image text
Answer #1

Ansues 82 Length-ot the-blbe L스 2000 fe- St C. pepe Vi 3 12 ˇ- 12- 5.28 4 0. 85 - Velo 580:53H千ー 120 + 580,53 Denalty ot walle ar 20e Cen veiting -the un8 62, 42, Los/u, tじ 131181,24 frAb sec S. p- 13118124 sif- 14 49

Add a comment
Know the answer?
Add Answer to:
2. 120 ft Pump Fig.2 Water at 20 °C is to be pumped through 2000 ft...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • Q2. 50 marks Water at 20°C is pumped at 5.7 m3 min-1 from the lower to...

    Q2. 50 marks Water at 20°C is pumped at 5.7 m3 min-1 from the lower to the upper reservoir, as in Fig. 2. The free surface of the upper reservoir is at height Z2 = 46 m, and of the lower reservoir at 21 = 15 m. The pipe diameter before and after the pump is D= 15 cm. Pipe friction losses are approximated by h = 27v2/(29), where V is the average velocity in the pipe. The gravitational acceleration...

  • 2. Water is pumped from a reservoir at rate of 2 f?/sec. from a reservoir 20...

    2. Water is pumped from a reservoir at rate of 2 f?/sec. from a reservoir 20 ft above the pump to a free discharge at 90 above the pump as shown. The pressure at intake to pump is 5 psig and pressure at discharge side of the pump is 50 psig. All pipes are commercial steel and 6 inches in diameter. Find (a) the head supplied by the pump. (b) the total head loss between the pump and the point...

  • A pump delivers water at 200C between a reservoir and a water tank that is 75[ft] higher than the...

    A pump delivers water at 200C between a reservoir and a water tank that is 75[ft] higher than the reservoir. The suction side of the system consists of a cast iron pipe of 1[ft]diameter with a strainer (Ks= 2.5) and four 90-degree bends at R/D= 5. The discharge side of the system includes a 1000[ft] long commercial steel pipe with 12” diameter followed by a gate valve. The NPSH required for the pump is 10[ft], and the design discharge is...

  • The value of (NPSHfor a pump is given by the manufacturer as 20 ft. Water is...

    The value of (NPSHfor a pump is given by the manufacturer as 20 ft. Water is being pumped from a reservoir at a rate of 25 cfs. The water level in the reservoir is 6.0ft below the pump. Atmospheric pressure is 14.7 psia and water temperature is 40℉. If the total head loss in the suction pipe is 4.0 ft, is the pump safe from cavitation effects?

  • AE 341347 Take-home Assignment #10 (1.5%) Name: ID Water at 20°C is pumped at the rate...

    AE 341347 Take-home Assignment #10 (1.5%) Name: ID Water at 20°C is pumped at the rate of 0.01 m'/s through a horizontal cast iron pipe of 26 mm diameter and 10 m long. Student (a) Calculate the pipe friction head loss i, in meters. (b) Calculate the required pump horse power. Assume the pump efficiency of 0.9.

  • Water is pumped from a well to a water tower (an above-ground reservoir) through a 330...

    Water is pumped from a well to a water tower (an above-ground reservoir) through a 330 ft long galvanized iron pipe (ε-0.0005 ft) with a 2-in diameter. The water surface in the well is 10 ft below the ground and the water surface in the tower is 60 ft above the ground. The water is to be delivered at a rate of at least 370 L/min. The sum of the minor loss coefficients is 2.1 a) Using the pump performance...

  • In order to provide irrigation, water has to be pumped to an elevation 120 m through...

    In order to provide irrigation, water has to be pumped to an elevation 120 m through a 600 mm pipe where the pressure required at the higher elevation is 172 kPa. The source of the water and the discharge point are at atmospheric pressure. Irrigation requirements dictate that water must be pumped at the rate of 1m3/sec. The loss of head due to friction and other factors is estimated to be 2.4m. Elevation of the water source is 60 m....

  • Two large tanks are open to the atmosphere at the top. Water s pumped from the lower tank to the upper tank through a si...

    Two large tanks are open to the atmosphere at the top. Water s pumped from the lower tank to the upper tank through a single PVC (smooth) pipe. The relationship between Velocity in the pipe (ft/s) and the pump head (ft) is given. There are no significant minor losses. What is the flow rate, Q (cfs), in the pipe? Pump Coefficients 1.30 sec /ft Pipe Length Inside Pipe Diameter 300 ft 0.250 feet a = 3.24 sec b 107.00 ft...

  • 3. (20%) Water of 15°C temperature is pumped at a rate of 0.01 m/s through the...

    3. (20%) Water of 15°C temperature is pumped at a rate of 0.01 m/s through the 800-m long and 10-cm diameter drawn tubing from the upstream reservoir at an elevation of 10 m to the downstream reservoir at an elevation of 30 m. The pump is located at an elevation of 10 m below the datum and at a distance of 350 m from the upstream reservoir as shown. (a) Find the values of the Reynolds number and the friction...

  • Water is being pumped from a lower reservoir to an elevated tank as shown below. The...

    Water is being pumped from a lower reservoir to an elevated tank as shown below. The pump is 80% efficient and rated at 200 kW. Determine the flow rate if the total head loss from point 1 to point 2 is 15 m. elev. 100 m 150-mm diameter pipe pump 180-mm diameter pipe elev. 50 m water

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT